【Upgraded】 SUMNEW 3387134 High-Limit Thermostat 3392519 Dryer Thermal Fuse 3977393 Cut-Off Switch 3977767 Cycling Thermostat Compatible with Whirlpool Kenmore maytag Replaces Parts 3399693 PS345113

Thought I needed to replace the fuse on my dryer. On the replacement part website, the fuse alone cost $26. Not a horrible price but this package came with the fuse, and all of the thermostats for $13. No brainer in my opinion. We replaced the fuse and all the thermostats and now my dryer works like new. It turned out that my fuse and thermostats were all relatively easy to get to and replace but ease of installation will be based upon the style of dryer and where the fuse/ thermostats are located. I am very satisfied with this product.

I was pretty sure my cycling thermostat was to blame for my dryer repeatedly shutting off for 20 minutes after one minute of run time, thereby overheating and triggering the shutdown. Bought this kit, not because I needed the other 3 parts, but because it was inexpensive and got good reviews. Swapped out the cycling thermostat but that didn’t fix the problem. Then the hi-limit thermostat, still no fix. Changed the thermal fuse and we’ve got a functioning dryer again. Not exactly sure why this fixed the issue, as the symptoms didn’t point to a faulty thermal fuse IMO. But I’m relieved by the outcome, and equally pleased that I inadvertently ordered the entire kit with “unnecessary” parts instead of just the part I thought to be faulty. Definitely recommend, and it will be nice to have those extra parts on hand should something else break in the next 25 years of this dryer’s life.

I tried one kit but it was with different company on Amazon. But this kit from SUMNEW worked perfectly! It was very easy to reinstall the new parts that any new DIY person could handle. My wife called this a dryer facelift. Our dryer heats better because the parts are better than the OE. Just put in your brand and model number in the search bar but again make sure you get SUMNEW. Their packaging was nice as well as each item was in its own bag. The quality SUMNEW was so much better. I know there are so many companies trying to get your business but look no further than SUMNEW. I don’t even work for them, they just have great parts that work!

My 2009 Roper/Whirlpool electric dryer wouldn't advance on the "Energy Preferred" setting, but it ran fine on the 30-minute high/low/fluff cycles, so I knew that the timer motor in the cycle knob was good, and the high limit fuse was good, and I'd already replaced the old heating element. Replacing the thermistor did the trick and now I can throw wet clothes into the dryer and get out dry clothes after a reasonable hour and a half or so, just like when it was new.It's only been a couple of weeks, so I don't know about the longevity of these parts versus the original Whirlpool parts that lasted over 10 years. However, even if I have to replace the thermistor once a year for the next ten years and even if I bought this pack over again for $20 and threw all of the other parts away, that would only be $200, which is much less than I would spend on a new dryer today. I certainly expect it will last longer than a year.The most expensive complex part of these dryers is the motor, and that's made pretty well. The other parts are either cheap or not hard to jerry rig. The parts most likely to fail are what you'll get here for very little money, so it can't hurt to try.Replacing the thermistor is a matter of 1) unplug the dryer 2) remove the back panel (8-10 screws) 3) find the original thermistor 4) remove the 1/4in screw (you might get by with a flathead screwdriver) and the two wires (needlenose pliers might help, but be gentle), and 5) see 4), 3), 2), 1) :-)Interestingly, the thermistor isn't actually needed for the dryer to run, but I think it runs full blast all of the time, which is a waste of energy, destructive to your clothes, and makes it a pain to do laundry since you can't just start the dryer and go to bed.

We have an older style dryer machine that we've had for about 10 years but it is much older and last month the belt broke. This month, it stopped heating. After a quick youtube search, I then did a conductivity check of the thermal fuse, we figured out that it was bad. Since unit is older I figured this kit would be best. Super happy with kit and fast shipping! SUPER easy to install, maybe 10 minutes if you have hand tools. it was literally 10 screws lol A++

My old KitchenAid Superba dryer has been worked on many times by me but this time was harder cause i couldn't figure out the issue. Heater was not heating but element and power all checked out so i saw this and the part numbers weren't exact except for one of the parts so i replaced all four and my dryer now works. not sure which one fixed it but for $7 I'm happy. I was just about to by a new dryer. to test the old parts take them off and test the resistance with a multimeter. there are a bunch of youtube videos explainging this. be sure to remove from the circuit then test.

I was a service tech for years and frequently fix appliances on the weekends for friends and family. I had one to fix that was about an hour and half away and did not have a parts store anywhere nearby. I replaced the belt on this before and it was not coding and the drum was still turning. I figured ignitor, thermal fuse or high limit. I wanted to one shot this repair so I ordered this kit. Put the fluke leads into the igitor harness, no juice, checked continuity on the thermal fuse and it was open. One screw it was out and the new one was in. I went ahead and just replaced the rest so I don't have to go back. Really worth it to have e everything on that circuit in one kit, made my day.

They're very cheap and don't last