🔧 Connect with Confidence!
The Delphi WeatherPack Connector Kit WP-1104 is a comprehensive 1104-piece set of sealed weatherproof automotive electrical connectors, designed for 20-12 gauge applications. It includes a T-18 non-ratcheting crimp tool and features a portable carrying case, making it ideal for both professional and DIY repairs.
T**K
Takes wiring to the next level
This kit is great. Case is nice and sturdy. Tools work every time with no issues. The selection of connectors and parts is great. Using this kit takes installing aftermarket wiring to the next level. Its tidy, sturdy, weatherproof, and you can reconfigure later if needed.
J**F
Nice to have
This set is nice. It has plenty of pieces to get the job done. Only complaint is the box is a little flimsy. But otherwise nice set.
J**N
Very nice kit
Kit is OEM quality and very nice with the included tools. Definitely what I was looking for to put in my shop for wiring repairs.
C**S
Don't skimp out. Buy this kit and be done with it.
I had a little buyers remorse at first, but as soon as the kit was delivered, I knew I was justified in this purchase. Very complete, nice stack on case. This is something that will always be close to my tool box. I get a little geeked out about stuff like this. So I am sure I will order more stuff for this kit, like 12 gauge pins and seals.
J**N
Need instructions!
I've never used weatherpack before now. I have used other connector systems from Molex. In any case, I like this kit. The parts work together, which is the secret of a good connector system.That said, I was expecting some sort of instructions. It would have been nice to have something that said, for instance, place the sealing gasket on the wire before crimping the connector to the wire. For that omission, I deducted a star. So, after doing this a handful of times (and messing up some connectors), here are my instructions to you:1. Determine which seal fits snugly, but not overly tight around the insulation on your wire. Set aside.2. Strip 1/4 inch from the wire. No more.3. Place the seal on the wire insulation with the narrow end toward the stripped end of wire. When correctly placed, the seal will match up to the end of the insulation where it was cut for stripping.4. Select either a sleeve or a pin, depending on which side of the connection you are building. The sleeves are used with the connector piece that has the factory-installed connector seal. The pins are used with the connector piece that the connector seal slides into.5. For the sleeve/pin, there are what look like three crimp regions. The large crimp is for the seal. The next, smaller crimp (with two or three tabs) is for the bare wire. The next "crimp" is not a crimp, don't hurt it (I made this mistake, this one helps hold the pin/sleeve in the connector shell).6. We will crimp twice. Our first crimp is for the wire. Using the supplied pliers, place the wire crimp region that you identified earlier (with two or three tabs) into slot three or four (depending on the size wire you are crimping, I haven't found a need for the smaller slots, but maybe....) You can always start with slot 4 and then use 3 or 2 if you think you need more crimp. One side of the crimper on the pliers is round and the other is like a 3 or w or lower-case omega. The open end of the crimp region on the pin/sleeve should face the "w" part of the crimper. If you close the pliers down ever so slightly, the pliers will hold the pin/sleeve while you do other things. Also note that the crimp region is sized exactly the same width as the pliers, thus you can crimp the wire in only one step.7. Now, insert your bare stripped wire into the pin/sleeve where the crimp will occur. Do not insert too far. Since you've previously placed the seal flush with the end of the insulation, that provides a guide of where you want to put the wire. This is why we only stripped off 1/4 inch in the second step. Compress the crimp with the pliers. I've got pretty strong hands and I didn't damage anything with unmitigated pressure, so have at it.8. Make sure that the seal is all the way up to its crimp tabs. The tabs are large and should be prepared to wrap around the narrow part of the gasket. Place these tabs into slot 5 of the crimper. Again, there are two sides. The open side of the tabs should face the side of the crimper that has long sides. Note that each zone of the crimper has a long side and a short side. The zones alternate, one has the long side on the right (as you look at the crimper) and the next has the long side on the left. If you turn the crimper over, the sides change from right to left and vice versa (I know, this is obvious, but it took me decades to get used to that, and I'm not sure that I still don't get surprised when it happens). when closed, zone 5 makes a circle that is exactly the size of the tabs closed around the seal. So now, we crimp. Make sure the seal is properly positioned between its tabs, then place the pin/sleeve into the crimper (squeeze the tabs together with your fingers if they are spread too far), then compress until the tabs are formed into a circle. I'm pretty sure it's a bad idea to over-squeeze here. If the seal was selected correctly to fit the insulation on the wire and the crimp was done right, the gasket will be firmly held in place.A SIDE NOTE: This kit doesn't have the right seals for 24 gauge wire, so either just live with it or find the right seals.9. We are almost there. Note that on the connector shell, there are letters, (A, B, C, ...) for each pin/sleeve location. These are matched between male and female connectors. By the way, Delphi calls the connector shell with the factory-installed seal the female side and they call the other connector shell the male side. The reason is that the SLEEVE connector goes into the female shell and the PIN connector goes into the male shell. For my part, since the female shell goes into the male shell, I get confused. Just remember that the sleeves go into the connector shell that has the factory-installed seal.10. Push the connector into the shell. Which end? Note that the shell has a fold down cover. This "strain relief" holds the seals into the shell so that the shell is more robust. By looking at the shell, you can quickly determine which end of the shell will get this cover. That's the end you insert into. However, this is a well-designed product. I inserted one the wrong way, pushed it in, realized my mistake, and then it just pulled out. No muss.11. When the connector is properly pushed in, it will click. The seal will be flush or recessed in the connector shell.12. Once all the connectors are pushed into the shell, fold down the strain relief and click the two tabs closed. Your connector is now complete.13. Build the mating connector.14. Now that the two halves are complete, they can be pushed together. Note that there's a plastic tab that holds the connectors together. This clicks into place.15. The connectors can be separated without tools. To do so, gently pry the locking tab up from the connector shell while pulling the connectors apart. When they have barely moved relative to each other, you can stop prying the tab up and just pull the connectors the rest of the way apart.
J**S
Complete.
I felt this kit had a great number of options and came with a crimper and tool set. What could be better? Neatly packed in a new case to hold everything and contact info for refills, etc. Great buy.
J**L
Awesome
Love it , everything is exactly what you would expect, crimp tool isn’t spring loaded but other than that everything is high quality
E**R
Great product
Great product came as advertised
Trustpilot
Hace 1 día
Hace 3 semanas