XHF 100 PCS 3/4" Black Self Adhesive Cable Zip Tie Mounts Wire Cable Clips Holders Management Anchors Organizer Holders Squares(HS-101S)

These work great with a dot of super glue...

These are very durable, perfect for managing a 75’ Ethernet cable, adequate size, and adhesion was way better than expected. It is important to note that this adhesive, as with most adhesive of this type, requires firm, even pressure for 10-30 seconds to properly adhere to a surface. When applied properly, these things were so firmly stuck to the wall that we needed to use a zip tie to pry it off the wall. We were honestly astonished to see that the plastic did not break or deform despite the serious amount of strength we needed to pull it off. We were pleasantly surprised to find that it did not pull the paint/vinyl off of any of the surfaces but in single a spot where the paint was already chipping and, even then, it was only a couple specks, it didn’t tear back a strip of paint or anything like that. I did find that this adhesive does not tolerate even the tiniest bit of moisture on the wall, though. (I hadn’t noticed that water had started to condense on the cold wall by the window, but I wiped it down and it worked perfectly.) Perfect for cable management, particularly in our case where we had up to three CAT6 cables in some areas to run long distances together. Tremendous value for the price. 10/10, exactly what we needed.

Exactly what I needed

Very adhesive great sir cleaning up clutter easy to use easy to install

These are absolutely essential if putting Christmas lights up on a house with vinyl siding and gutters! That’s exactly what I did with these and zip ties. Get both colors; a bag of black and a bag of white, trust me. A tip though: if using them on your house like I did for Christmas lights, get an old rag and a bottle of rubbing alcohol to clean the area you’ll stick these to before applying. These have a pad of 3M double sided foam tape and stick well, just make sure the surface you’re applying to is clean.

I don't like the pegs they ship with PCB kits now. I use these nylon tie mounts because it makes it easier to remove and re-base PCBs if you decide to install them into a different electronic housing. The pegs "punch" through the holes of the PCB substrate plastic and I'm worried the pegs will crack the substrate and possibly damage the PCB electrical trace, too. I use the tie mounts for arcade controller (joystick) PCBs. You only need to install two of these two zip tie mounts diagonally from each other to stabilize a PCB in an enclosure (joystick base). I've done things this way for over 12 years now. IF the adhesive fails OR comes loose, you glue the tie mount onto the enclosure with hot glue. I'd give it at least 15 minutes for the glue to harden BEFORE you reinstall the PCB with nylons ties. Oh, and be careful NOT to seal in the holes that the nylon ties slip through. That's the only problem I've had with reusing the tie mounts. You shouldn't run into reusing tie mounts with packs of 100 of these bases unless you're doing a ton of projects...

Work great. Used outdoors for lights and decorations. Holding well in cold and rain. Much easier and not damaging than nailing/stapling. Be careful where you stick if you plan to remove. I may take light weight materials with it.

Fast and easy to use

السعر مبالغ فيه ، الصمغ جيد لكن لو كان أقوى أفضل ، اللي بيشتريه راح يخدمه

The 1.1” stick on ties are not 1.1” and are about 20% smaller. I was not accidentally sent the incorrect size because the item I received is in between the two advertised sizes.

This is a good item, very useful to use along with steel ties in hard to reach and tricky situations.

Would buy again

Me vende 500 y envía 100. No me gustó esto del no proveedor. El producto no es malo. Aclaro esto para que no se dejen guiar por lo de mala calidad.