AUXMART Upper Windshield Mounting Brackets for 52" LED Light Bar Replacement for Toyota FJ Cruiser 2007-2014 (1 Pair)

these brackets are well worth buying as they are easy to install and look awesome as well as inexpensive. i have them holding a 52 inch curved light bar and they work perfect and look awesome.

A lot of the previous reviews reported the "FJ" was backwards. It looks like they've since sorted out their cuts. Mine are proper and of good quality. Very sturdy. I have a 52" LED lightbar installed now.Also mine did come with spacers an all bolts to replace. I will say that the bolts are not coated and started showing some surface rust. I went ahead and just sprayed them with Rustoleum.FYI. When removed the Torx bolts from your roof GO SLOWLY! They strip extremely easy. One of my stripped so bad about half way out. I was able to take vice grips and get it the rest of the way out.

Ok. Read a few reviews.1. I did cut my brackets 4in shorter using a big washer as a template.2. I used bed liner paint for another coat.3. Used my own hardware from home Depot. ..nylon washers.see if there's any more problems.UPDATE.3 years later....Rust did form.Sand down/ paint and reinstall.I like the straight bar look, although the curve does look appealing but it does the job.Considering the price a little manual labor...is free.My application does not make any noise whatsoever. I'm content. Smiling....

Got this for my boyfriends FJ. He installed this himself. According to him, the install was easy and smooth with the 52" curved light bar. All he needed was silicone to make sure there's no leakage when it rains when he drilled the holes to install the mounts. We've been off-roading on some bumpy trails and hills and the light bar is still intact in the same position. Overall, he's loving it! He says it's worth it!

do not fit well. need to bend to make them fit the 52" lightbar. rubber washers do not work well to seal. they are to thin.

As stated in many reviews they are not very strong. Allows light to wiggle side to side making very annoying on trails. Shortened arms and brought tighter to roof line.

Love it, made of good metal, the powder coating was pretty good too. I had to cut a little into the holes where the bolts go because i accidentally bought a light bar that was bigger than the recommended size.

I've had multiple customers over the last couple of years ask me what's the difference between these and the light bar mounts from RESZ Fabrication. I never really had a clear answer until now - I finally purchased a set to do a comparison. I'm going to break this down into "Likes", "Dislikes".LIKES1. It positions the light bar perfectly above the windshield.DISLIKES1. These were NOT designed for a curved light bar as stated in the title and description. There is no relief bend in the mount to account for the angle of the light bar mounting location on each side. If you bolt these to a curved light bar, you are creating a tremendous amount of stress on the mount by tightening that bolt down to secure the light. Over time this will lead to stress marks and eventually break.2. These mounts are from thin 1/8" steel, not 3/16" steel like they advertise in the listing. These are extremely flimsy and allows for quite a bit of side to side movement of the light bar.3. Very little material at the end of these mounts where they mount to the light bar. Stress from vibration will eventually cause failure vertically from these bolt holes.4. The mounting points that mount to the roof rack are only bent to 90 degrees and doesn't account for the angle of the roof rack mount itself. Therefore the mount angles outwards if you're looking at them from the front of the truck.5. The spacers they provide to sit inside the holes of the roof rack itself are extremely small. They are supposed to be used to keep pressure off the roof rack mount and provide a more secure fitment. These tiny spacers do NOT provide that, which is going to create even more vibration/movement.6. The "FJ" logo sucks!BOTTOM LINE - These mounts are ticking time-bombs!! They will work for a short period of time. A little bit longer if you use a straight mount, but eventually they will fail and that light bar is going to end up on your hood.I added a few pictures to show the comparison between these and RESZ Fab mounts.