amFilm [2+2 Pack OneTouch Tempered Glass Screen Protector for Samsung Galaxy S23+/S23 Plus 6.6 Inch with Camera Lens Protector, 9H Hardness, Easy Installation and Bubble Free.

I have never installed a screen protector before, so I was nervous. But this one was a breeze.To prepare my Samsung S25+:I did have to take off my phone case before I could install the screen protector. The handy dandy installation tray didn't fit with the case on.I cleaned the phone screen like a mad woman with the included wet wipe and microfiber cloth.Then I used the large sticky dust remover over the entire phone. Looked clean as a whistle.Then I removed the plastic covering from the protector tray using the attached tab.I then placed the plastic installation tray over my phone and pressed. I pressed the top and ran my finger down the tray a few times, slowly.When I removed the tray, it looked amazing except for one little spot on the bottom....it looked like there was a speck of dust on the screen, so the protector would not fully adhere in that particular spot.Since this package came with 2 protectors, I thought I couldn't hurt anything to try and fix it before I resorted to using the 2nd protector. So I ever so slightly lifted the corner of the newly installed protector off my screen (easily done with my finger nail) and I used the provided small dust remover sticky tab to touch the screen and grab that annoying lint from my phone.Once I did that, I released the protector and it laid back down perfectly. It adhered to my phone with no bubbles or spots. I did a few once overs with the microfiber cloth, just to make sure it was stuck.Once in place, I put my phone case back on and it looks great.After the install, I rescanned my fingerprint, as recommended. It seems like I might have to press my finger down on the screen just a bit harder now, but otherwise, it recognized my fingerprint and logged me in.NOW - this was just a review of the INSTALL. I have not used this in everyday life and verified that it does protect the screen. But the installation was a BREEZE!!

Let me tell you how extremely happy I am with this screen protector. This protector (both screen and camera lens) was put to the test and proved its mettle. I recently fell on an escalator, while holding my phone. I am not small. Reach out my arms to stop my fall, with phone in hand, and proceed to drive the phone right onto the teeth at the edge of the escalator step in front of me. The phone saved my hand from injury and the amFilm screen protector saved my phone. The protector is not shatter proof, as that is impossible, and with sufficient force it will indeed shatter. However by taking the force of the hit my phone's screen was completely undamaged. Completely intact. I should have taken a picture of the damage but let me just say that it didn't just crack, or even just shatter, it was pulverized at the point of impact and spider web cracks spread from there. I was positive there must have been some sort of damage under the crushed glass, but the screen was perfectly intact. After dropping the phone on gravel the cameral lens chipped and cracked. Only by using a utility knife blade could I pry off the lens protector, which came off in one clean piece, no fragments. Which, now that I think if it, I should mention that when I removed the screen protector, even with all of its damage, it pealed off cleanly and in one piece, no fragments.Then came the day to install the spare protector leftover in my original two-pack. I cleaned my work area as dust was a problem for my last install. Then proceed to install both the amFilm on my personal phone and, while I was at it, install a company provided $45 ZAGG screen protector on the new company provided phone. I started with the ZAGG on the Pixel8. Simple instructions. Followed the instructions. Applied the glass, and spent 10 minutes smoothing out air pockets under the glass and ultimately it didn't fully bond to a sliver of the screen in one corner.Next came the amFilm. By just previously installing the ZAGG did I then fully appreciate how much easier, precise, cleaner, smarter the amFilm application process was. ZAGG has you place the phone into a bracket that contains small nub posts that are for alignment of the glass. You then have the handle the glass itself, position the glass on the posts while not touching the adhesive, not letting it touch the screen too early, and sweating the whole time while you attempt to get the proper alignment. Then you are smoothing out the bubbles from under the glass for the next 10 minutes. I don't apply screen protectors all day, as if I worked at a retail phone store, so I'm sure there is a better Pro technique than just simply following the included directions.Now, compare that install to the amFilm. Same cleaning and prep. But some things are just smarter, which translates to better. First, there was a dust removal "sticker" in both kits. The ZAGG had a small rectangle that 2 fingers can hold, and you need to tap that sticker all over the clean screen to remove dust that might have come from the cloth wipe or fall from your person. That's a lot of tapping and motion over the screen that might allow other dust to land while your are moving your hand around. In comparison, the amFilm has a single sticker so large it covers the entire screen. You apply this sticker in a rolling motion to avoid bubbles and leave it there until you are ready for the last step. When ready you peel off the dust sticker and hustle before any dust lands. Next you hold the plastic alignment bracket, that also holds the glass within it. You peel the film from the glass and gently maneuver the bracket until it fits over the phone in perfect alignment. The interesting part is that the glass doesn't yet touch the screen, until you press down with your finger. You then Slooooowly slide your finder along the bracket opening, from top center of phone to the bottom. You will see the glass make contact and a wave of solid bubble-free clarity crawls across the phone. Then you remove the bracket and in the same motion remove the top film from the glass. I was simply amazed that there were zero bubbles. No time needed to scrape away bubbles and hope the glass is bonded. Plus the bonding was complete, all the way to edges and corners. Unlike the ZAGG which had the one loose corners that didn't quite bond and I know dirt will collect in the gap over time.Bottom line: Amazingly strong protection, difficult to scratch the glass, removes cleanly, applies flawlessly and stress-free. Did I mention there are 2 protectors in a pack, includes camera lens protectors, and is reasonably priced??

This thing literally works like magic! I have never been so satisfied with a product so much as this that I was compelled to leave a review. I always install a screen protector on all my phones, and it is a tedious, annoying, stressful process, because i try to avoid air bubbles, and end up wasting multiple screen protectors, and lots of wasted time. And when I read this "Auto Alignment OneTouch", "Bubble Free", "30 seconds installation".... I thought these were all buzzwords, and marketing tactics to get you to buy it. But to my surprise, this is the quickest installation process i have ever done for a screen protector. It was extremely fast, and almost no air bubble. There was only a little air bubble at the edge, but i could easily press it out. The process was probably 30 times easier and more convenient than the previous manual screen protector installations I usually do. Would definitely be getting this again whenever I switch phones or it cracks.