3D Printer PEO PEI Cool Build Plate for Bambu Lab X1C/X1/X1E/P1P/P1S/A1 3D Printer,Smooth PEO+Textured PEI Surface 257x257mm Spring Steel Plate,Double Sided Flexible Sheet Removable Platform

works like the one that came with the printer

Seriously satisfying adhesion for PLA, PETG, and beyond. No tape, no glue—just clean prints that pop off after cooling. It’s flat, durable, and worth every penny. Makes me feel like a professional... even when printing frogs.

Great build plate, Instant Adhesion on first layer right away. Bought a few more just to keep on hand. One downside I have is that I have to wait for the build plate to cool off has the prints usually adhere soo well I can break my print if its on the small and delicate side, flexing the plate doesn't even break away the prints. So I just swap the build plate right away to keep printing as the fresh plate cools down.

UPDATE: Leaving the below to show progress of my mistake/lack of accuracy. The seller reached out offering a full refund due to my review. Which is an awesome level of support. I was not even looking for a refund as I definitely use the plates all the time for PLA/PETG. My first use was ASA on a very long tall print that definitely pulled up a corner of the build plate while in the printer. During the discussion with the seller they asked for me to verify thickness between the two brands. The Bambu dual textured PEI plate is ~.55mm, with the RETUXEP smooth/textured plate measuring ~.72mm, and the textured/cf pattern plate ~76mm. So their plates are actually thicker than Bambus. They are definitely more flexible though.The build sheets look to be well fitted to the spring steel plate and work well when used properly. the only issue I have for this product is that no where in its listing is the thickness listed and the reason why I imagine is that it is thinner than the Bambu sold build plates. Most print materials this likely wont be an issue but for anything that warps or shrinks as it cools (ABS/ASA/etc) the plate is so thing that even the smallest of parts can pull the build plate up from the magnet on the printer. Also be careful as some of the ones I have come with sharp edges on the spring steel that you could potentially get cut on or scratch up the printer build area when removing/installing this plate.

Hate to jinx it, but this plate has been awesome. Very few issues, the ones I've had are likely just from me being too lazy to wash it like I know I should. After washing with dawn and hot water, it's not failed my yet. Small prints like earrings are actually stressful to remove because I'm afraid they're sticking too well to remove, even with the plate fully cooled.Will buy again, just to have one to swap out immediately instead of waiting.

I've had one of these impressive Bambu P1S printers since Christmas and every print until now has been perfect - unfortunately the very first print on the smooth PEO side of this PEO/PEI plate immediately failed and I had to abandon the print job. Whether the problem is lack of adhesion or wrong temperature or some other issue, I don't yet know, all I know so far is that this is not a direct substitute for the plate that comes with the machine and cannot be used 'out of the box' with the default parameters and standard Bambu PLA. I'll go read up on it and see if this is something that can be fixed by tweaking the configuration, but if that's what's needed then a note to that effect on the product page would have been welcome - all it says is "PEO build plate surface can print PLA and TPU and PETG." and "suitable for Bambu Lab X1C/X1/X1E/P1P/P1S/A1" with no indication of any config changes being needed. (I don't mind a product that requires some effort to use, I just would have liked to know up front, rather than assuming it would be the completely effortless process that the Bambu system has supplied so far. If the problem is that the proprietary Bambu system doesn't allow 3rd parties to print the QR code on the plate that tells the printer how best to use it, then that would be worth mentioning on the product page as well)ADDENDUM: I found online advice to manually set the build plate type to "Smooth PEI plate/High Temp plate" which I did - the fifth image shows that this did not work either. I only bought this for the smooth side but that's the side that just doesn't work. I'm downgrading my review from 3 to 1 star now that it's more clear that it's not my fault. I should have read the other reviews before buying.

Works greathigh qualityFast shipping

⭐️⭐️⭐️⭐️⭐️ Seller had Super Fast Shipping Very Nice item in Very Good Condition with a High Quality Appearance Very Good Value for the Price ⭐️⭐️⭐️⭐️⭐️