Mounting DreamSpeaker Stands Height Adjustable for Satellite & Small Bookshelf Speakers, Set of 2 Floor Stand Mount for Bose Polk JBL Sony Yamaha and Others - 11LBS Capacity MD5402

These stands are great, I especially like how they work well on both wood floors and carpet with the small carpet spikes included. Assembly was easy. These are pretty sturdy. I use these with my Samsung HW-Q990D surround speakers, and they fit perfectly. They sit fine on the base, but you can also attach them to the back with the sliding mount for additional support. The base is just the right size. The only issue that you may have is that the lowest height isn't very low. It's just right for my setup, but if you have a low sofa this might be an issue. Check the height.

Works great with samsung Q990F rear speakers. Just run the end wire first from bottom feed it up instead of down. and most likely you will need an power extension amazon basic sells 2 for like 7 dollars worked great because the wire speakers are short. And also some screws but single slide pole held it good.

These stands were solid and easy to install. Only issue, base “A” to Post “B” the holes didn’t line up as easily as the other stand. But my Samsung 9500rear speaker kit fit well!

I've purchased Mounting Dream products before such as their TV wall mounts and I have always been happy with the quality of their product and they inclusion of additional hardware to help simplify installation no matter which brand of equipment you are mounting. The Mounting Dream Speaker Stands for Satellite & Small Bookshelf Speakers is no exception, this is a quality product. Plenty of additional hardware and concise directions ares included to ensure that installation is painless regardless of the type of speakers you are mounting. The stands feel heavy and sturdy and give an impression that they would not be easily tipped over. The hole on the tube allows for you to easily hide cables whether it is a speaker cable or two prong power cord. The only thing I didn't like about this product is my Sony Z9R speakers look terrible mounted. The stand is so massive including the plate that the speaker rest on and the hardware is so large to allow for larger speakers to be mounted that my speakers just look ridiculous on this huge, sturdy stand. Hardware protrudes down and forward away from the stand and you can see the holes drilled into the resting plate (see pictures). I'm hoping I will get used to it otherwise I will have to pull out my Dremel tool and make some modifications.

Why did you pick this product vs others?:I bought the Nakamichi Dual 12" Dragon system, but the surround Dragon stands weren't available, so I tried these. These were rated at holding 11 pounds. The dragon surround speakers weigh 9 pounds. They work GREAT!! The only issue was the speaker mounting holes. I would have to drill a custom hole in the stand to use the 2 screw holes in the Dragon surrounds. With the bracing that comes with the stands just 1 screw seems to hold the Dragon speaker very well. I also think these stands are udder rated at 11 pounds. They are VERY sturdy. The stands come with rubber screw-in feet but also have carpet spikes in the parts bags if needed. I'm using the rubber feet. The adjustable height is another feature that the Dragon stands don't have.

After about 30 minutes of assembly time I was able to set my surround speakers up. My wife was pleased with the look of the stands so all good there. I removed the foot pads and replaced them with carpet spikes and honestly that took the most time. I measured so each spike was the same height as all the others and the stands sit well in the carpeted floor. The two tubes are screwed in place with hex screws with a screw knob in the middle of both tube to adjust the speaker height. I have them extended all the way to the max height of 42 inches -- which puts the rear surround speakers at a nice position above the back of the sofa. The speaker power wire is run through the back of the top tube and exits out the bottom. The resultant look is clean and the stands hold the speakers securely. The stands come in a powder coat finish so they look to be scratch resistant.As far a tip-resistance goes, I am sure you can knock them over with a heavy blow but otherwise the wide base makes them somewhat immune from easily tippling over. If tip-resistance is important to you then I recommend adding some lead weights in the base to give the stands more weight. I don't think that is really necessary. I tried to tip them over with increasingly stronger pushes and I was satisfied that under "normal" conditions they won't easily tip over.My only suggestion to the manufacturer is that instead of the knob to adjust height you should just supply another hex set screw which makes for a cleaner look. Once set I do not plan on changing the height.Really nice speaker stands. Highly recommended.

I bought these for my 2024 Samsung Q series (930D) soundbar satellite speakers and they fit great. The quality is great for these inexpensive stands, less than $100. I've seen stands 3 times more expensive and don't find it necessary to spend that much on two speaker stands. These will fit multiple brands of small speakers because the product comes with a wide variety of mounting hardware.

This was easy to put together and does the job for my Samsung Q990D setup. The only thing is that the plugins are too fat for the pipe so you'll have your wire outside. To me that is not a big deal & also not the stand's fault.