ICM ControlsICM281 Furnace Control Replacement for OEM Models Including Carrier CES0110057-xx Series Control Boards

Purchased the ICM281 CESO110057 for our Carrier 58PAV090. After 22 years of service, our Carrier furnace appeared to be down for the count. Thanks to an assortment of valuable info gathered from various forums and youtube videos, we were able to narrow the problem to a control board issue (cold solder joints) plaguing some Carrier furnaces.-Old Control Board-Basically, the furnace's hot surface ignitor (HSI) would light up fine, but for some reason the main burners wouldn't fire up and after 4 attempts it would go into "lockout" mode and shut the entire system down.We were told that we could restart/reset the system at the thermostat by turning it off and then back on, in order to get it to come out of lockout mode. Well, we discovered that the furnace could still fire up on occasion after approx 4-6 re-starts during the daytime and 9-12+ resets during the cold night. Inconsistent heat is better than no heat, well... not by much.There was only heat if you have the patience to reset it several times and each reset would take approx 5 minutes each to complete. While waiting for the new board to arrive, getting up in the middle of the night to wait for the furnace to start up after each reset was the pits. We did install a WIFI thermostat and an IP camera in order to NOT have to get up by the thermostat to reset it, but this morning it took 23 resets and there was still no heat. Didn't continue because it was time to get to work.-New control board-So this morning we get an alert saying that the control board will be delivered one day earlier. Hallelujah! Sure enough, the board arrived on the porch this evening and I quickly went to work. Unplugged the furnace, unscrewed the various covers, and pulled out the old board. Not too difficult, there are plenty of videos on youtube that give you a good idea of what to watch out for and how to do it. It sort of felt like building a PC, except I actually bothered to label all of the wires just in case I forgot where they go on the new control board.It probably took about 35 minutes of actual work, I took photos of the wiring at every step of the procedure to make sure that I didn't cross wires or leave anything off. Once complete, I double checked everything, screwed the covers back on, and then plugged in the furnace. Turned on the heat and for every second there was silence, it seemed like an eternity. Fortunately, the inducer kicked in, the ignitor started to glow, and to my surprise not long after that, the burners kicked in! What used to take about 5 minutes (x 23 attempts), now took about a minute. Saw beautiful blue gas coursing through the chambers of hte burners. Never thought I'd be that excited about gas, but after several freezing nights, it was a sight for sore eyes.Thank goodness for this new control board, what a relief and what a difference a board makes!

My original board was failing to open the gas value (guessing a bad/stuck relay) so I shopped around and discovered replacement boards were considerably more expensive than this one pretty much everywhere else I looked (like 2-3x more). This price seemed too good to be true but I trusted that Amazon Prime would take care of me if it was a dud. I took pictures of the wiring on my old board so I could be sure to reinstall everything in the same places on this new board. Strangely enough, it didn't work--I got a fast blink from the small LED. The instructions mapped this to "reversed polarity" so I simply swapped the two output wires from the transformer and it roared to life. Not sure why I had to do that since they weren't swapped on the old board (and the instructions confirmed my first attempt should have been correct based on the colors of the wires) but it's working fine now. (And yes I confirmed with a multimeter that the white & black 120VAC input wires had the correct polarity--black to ground reads 120, white to ground reads zero.)My old board didn't have the diagnostic LED. If this board didn't have it either I would have given up and returned it as a bad part, but the fast blink and detailed instructions were enough to tell me what the problem was and how to fix it. Still baffled about why the working configuration doesn't match the instructions (and I considered knocking off one star for that), but the board is performing well and I have heat now so nothing to complain about. :-)

I was pretty happy, but had secondary problem with furnace. I suspected gas valve based on error codes. I hired a repair company, but the mechanical repair guy blew 2A fuse multiple times then put in 5A fuse, shorted it out big time and fractured ed the board. That was about 1 year ago, and a cold Thanksgiving holiday. But I liked the board, instructions etc. I installed it myself and thought it worked well. The repair company replaced with OEM board. I can say the docs are better, and I’d definitely buy again.

Exactly replaces the circuit control board in our good, old Carrier high efficiency gas furnace, and it has a diagnostic LED in the event of troubles in the future. Removal and installation was easy. Skill required is basic. Instructions are quite clear. I was not able to sort out the failed component failure of the original circuit board so complete replacement was the best option. Price is so good, too.Completely satisfied. I share these photos of wiring placement and visible faults in old part for your benefit.

Replaced CES0110057-00 with ICM281 in Carrier Weathermaker 8000 series 100. It was direct replacement +LED error codes diagnostic. It immediately detected power reverse L-N. Love it. Like reported in other review, it fixed main problem of furnace needing several thermostat resets to release lockout (don’t know why happened).

It was easy to install and worked like a charm when I switched it on. The card came in without any damage on time, packaging was decent. All the connections matched perfectly.