2 Part Epoxy, Incredibly Strong Bonding, 5 Minute Set, 0.85 oz

★★★★★ Excellent epoxy for repairs! I used this Gorilla 2-Part Epoxy to repair my Murphy bed, and it worked exactly as I hoped. The bond is extremely strong, and once it cured, the repaired area felt solid and secure. It was easy to apply with the syringe, and the clear finish looked clean. One important tip: make sure you mix both parts thoroughly before applying. If you don’t mix it well, it won’t cure properly and may stay sticky or fail to bond. Overall, this is a great product for furniture repairs and projects that need a strong, durable hold. I would definitely buy it again.

Very good, very strong glue. I don’t think anything can take it off this camera’s protection cover from the wall of the house (outside) without smashing it into pieces. Not a chance. Glued plastic to concrete/stucco wall. Easy to use. Comes with double chamber tube, so you just squeeze out the content to a small tray, mix it these two together & use it within 5 minutes. After mixing, it becomes very thick very sticky glue in whitish color. Dried clear. Dried (to touch) quickly within 30 minutes (depends on thickness applied) & cure completely in 24 hours for sure. Can be painted over if needed. Because it’s thick you don’t need 100% flat surface only close & patch in the gaps. Make sure to have gloves on.

I first acquired this epoxy to repair a custom, cast, resin, wall sculpture of a Great Blue Heron (in flight) that a visitor had removed and dropped, causing it to shatter into four pieces along its four foot wing span. Initially, I also purchased three foot long, aluminum braces to reinforce the sculpture’s wing span. To my amazement, with only a modest amount of this Gorilla-brand epoxy applied to the joints between the broken pieces — and no structural reinforcements — the entire wing span of the sculpture is fused with such strength and rigidity that I can support the entire weight of the sculpture (80 lbs.) at anywhere along the wing span without it flexing or coming apart. This is really astounding. The entire sculpture may actually be materially stronger than before the repair. For safe measure, I added a smear of the epoxy along the back side of the sculpture along all along the fracture joints. It is now so rigid and strongly bound that I can tap the tips of the wings and the entire sculpture resonates like a metal gong, which means it is, for all practical purposes, fused into a uni-body entity. Some tips: 1. There’s a plastic wand wedged between the push-rods of the dual syringe. You need to break this wand out of there to be able to fully depress the syringe. Personally, I found a wooden popsicle stick to make a much better wand for mixing the epoxy and applying it. 2. You’ll know that the epoxy components (resin and hardener) are properly mixed when you can smell a temporary stink like rotten eggs. Soon after, the epoxy will catalyze and generate heat. From that point, you have 5 minutes to apply the epoxy before it starts to thicken and set. Thus, to maximize your work time, you can start applying the epoxy as soon as your smell the pungent stink. The stink goes away as soon as the epoxy starts to set. Full strength and cure, which is when no tackiness can be felt in the epoxy, occurs at around 24 hours, 3. The epoxy has a thick consistency, like honey. It fills small gaps extremely well and will self-level to an extent, removing brush strokes and smoothing over depressions. It is clear with a very slight amber tint. It goes on clear and cures to a clear, tough-as-nails finish. 4. I recommend wearing nitrile gloves as you work with this epoxy, as if it gets on your skin, you’ll need acetone to remove it. Acetone is very effective at breaking down this epoxy before it cures. However, once it cures, the acetone will not soften or dissolve it. 5. If you want to shape or flatten the epoxy — on the back of a sculpture for example — after it sets, you can lay the side of the item with the epoxy against a polyethylene sheet on a level floor or table top. The epoxy sticks like crazy to resin, metals, wood, stone, glass, leather but will not adhere to polyethylene plastic. After the epoxy cures, you can pull away the polyethylene sheet and the epoxy will be hard and smooth like glass. It will bond strongly to 3D printed thermoplastics like PLA. 6. As long as you keep the resin and hardener separate, these components will last a surprisingly long time. Working over several days to join each fractured piece of the sculpture, I left the nozzles of the double syringe uncovered and the epoxy components easily remained viable for several days. For longer term keeping on any open syringe, just stretch a section of duct tape over the nozzles. 7. Where a really clean joint is needed, applying the epoxy to just one side and pressing the parts together will give surprisingly strong adhesion. However, for maximum strength, I recommend applying epoxy to both sides of a joint and letting a “bead” ooze out along the joint. On the cosmetic side of your project, the bead can be smoothed out before the epoxy cures. I recommend leaving the raised bead on the non-cosmetic back side of any such workpiece, and after it cures, coming back with more epoxy to smear over the bead to create a wider seam patch for maximum joint strength. The fresh epoxy adheres well to any old cured epoxy. The stuff is for certain a resin, and will practically weld any resin components into a rigid uni-body. This epoxy lives up to its brand name of being gorilla strong.

As is often the case, my experience with the Gorilla 2-Part Epoxy, Clear Epoxy, 0.85 Ounce Syringe was largely in line with expectations. The product description accurately portrays what you get: a two-part epoxy designed for rapid, strong bonding. For its intended purpose, it certainly delivers. The "5 Minute Set" claim is pretty accurate, meaning you don't have a lot of time to fiddle around once you've mixed the two components. This is great if you need a quick fix, but it also means precision is key from the get-go. The bond itself? Incredibly strong, as advertised. I've used it for a few minor repairs around the house, and each time the repaired item feels as solid as new. It held up perfectly to the tasks I threw at it, providing the kind of durable bond you'd expect from a brand like Gorilla. The clear aspect is also a definite plus, as it doesn't leave unsightly colored marks on the repair. However, where the product falls a little short of being a truly stellar five-star item for me is in its usability, specifically the "messy to use" aspect. While the syringe packaging is generally convenient for dispensing two parts, I found that getting a perfectly controlled and clean application was a bit of a challenge. There's a slight tendency for a tiny bit of overflow or for the mixed epoxy to ooze a little more than I'd ideally like, even with careful pressure. This isn't a dealbreaker by any means, but it does mean you need to have some paper towels or a cleaning cloth handy and be prepared for a bit of cleanup afterwards. It’s not quite as neat and precise as something like a glue pen, for example. Ultimately, this Gorilla epoxy is a solid, reliable product that does exactly what it says it will: create an incredibly strong bond quickly. It earns a solid four stars from me because it perfectly meets its functional description and delivers on its promise of strength. It’s a great go-to for repairs where durability is paramount. However, the minor messiness associated with its application keeps it from reaching that elusive five-star status of being truly exceptional or exceeding expectations in every regard. It's a good tool, but not a perfect one.

If you work with 3D prints—especially slicker plastics like PETG that standard super glue won't stick to—this two-part epoxy is magic. It mixes cleanly, sets up within a reasonable window, and cures into an absolute rock-solid structural bond that won't snap under tension.

The Gorilla two part epoxy worked beautifully for my application- a broken mounting bracket for a rather heavy refrigerator drawer pull. The pull has an internal plastic "block" that is essentially the bridge between the pull and the mounting post on the drawer face. The block receives the mounting pin on the drawer face as well as the bracket and screw tab for the handle. It was broken into two pieces and useless. A new handle was $145! So, plan B- epoxy. I've used many varieties of two part epoxies in more applications than I can list. Some manufacturers/products are better than others. Some are easy to dispense and work with; some are not. I was extremely satisfied with the Gorilla brand epoxy. The dispenser was simple and effective. As a nice bonus, the blister packaging is designed as a mixing tray. The epoxy was not crystal clear, but nearly devoid of color/tone. I mixed it smoothly and got no air bubbles- which can plaque two-part repairs. The consistency was Goldilocks right- not too thick, not too thin, so the manufacturer's proportions for both compounds was s[pot on. Workability/working time was perfect- about 4-5 minutes before the compound firmed up. I let it rest/cure for 24 hours before re-installing the pull because I applied it thick- basically filling the pull's mounting housing. Once installed, I was thrilled! The drawer takes a reasonable tug to open, and as you can hopefully see in the attached video, the bond is rock solid. I saved $135 and the drawer operates better than factory.

This epoxy arrived exactly as described. The packaging was intact, the syringe was undamaged, and everything appears to be in perfect condition. I purchased it to keep on hand for future repairs because I've had excellent results with Gorilla two-part epoxy in the past. It has consistently produced a strong bond and cures clear, which is why I continue to buy it. I haven't needed to open this particular syringe yet, but based on its condition when it arrived, I have no concerns about keeping it in my repair supplies until it's needed. Everything arrived exactly as expected, and I'm satisfied with the purchase.

This epoxy is very clear and I give them credit for that. But one tube is much more viscous than the other. As a result, when you push the syringe, often much more comes out of one tube than the other. So that can be messy and lead to improper proportions. Maybe they could compensate for that by changing the design of the syringe for the two tubes, for example giving a larger outlet to the more viscous one.

pegamneto muy fuerte y resistente, aun a través del tiempo conserva sus propiedades. fácil de preparar. yo le usado para sellar unas conexiones de tubería y me ha funcionado muy bien. solo hay que dejar secar por al menos 12 horas sin contacto con el agua o presion

جربت انواع كتير ، ده أفضل نوع. طبعا أغلى كتير من أي نوعية اشتريتها ، صناعة امريكي.

Although there was a problem with the product, the seller has went over and above to resolve the problem. you can't beat that. Thank you!

جربته بلاستك مع حديد وانتظرت ٢٤ ساعة وانفك بسهولة مع اني اتبعت التعليمات

強力な接着力で短編満足しています。