Grip Puppy

Let's be honest, these are NOT going to reduce 100% of the vibrations felt on the handlebars, however, they will reduce a good portion of those pesky vibrations. Mine are installed on a Honda Goldwing DCT. Absolutely NO COMPLAINTS!!

not easy to put on but once on it will not slip. more comfortable then the hard grip that come on the bike. The bigger grip makes less hand fatigue.

I was prepping for the Daytona Rally run last month and ordered these. The premise was that the extra cushioning would cut down numbness and such in the rider's hands. I broke my wrist when I was younger and my right throttle hand goes numb pretty quickly unfortunately. ANYTHING I can do to delay or prevent that is a plus.First trick was getting them on though. Read MANY "Here's how I did it" things. Did the hot water, tried the dish soap. What a pain in the "you know where." DO THE AIR COMPRESSOR METHOD. I fought and fought before I broke out the compressor thinking that it couldn't be that hard. It was.Pinched the end of the grip around the tip of the air gun, gave a little blast and it was about halfway on in a split second. Had to fidget with it a bit keeping the air blast in there enough to balloon it up to move on further. Still took some effort and fidgeting, but yeah, that was the absolute best way. It is tougher as you get it nearly on as it's almost impossible to pinch the end around the air gun nozzle. It will eventually get there though. Might have tried a longer needle tip to get further inside the nozzle. Don't HAVE one, but I bet that might be the trick.Did it work AFTER I got it on? Yes. My right hand often goes numb in just a few minutes without flexing it around. I have a feeling that the extra circumference on the grip as well as the cushioning was a huge improvement for me. Was able to ride pretty happily for much longer without having to shake out that hand. They're staying on!As well, as in the pics, I was able to add the throttle control back over the top of the grip. ALSO took a little fidgeting, but it's on, works great. SUPER HAPPY with my setup now.

Glad that the Big Paws are inexpensive! The stock grips on my Indian Challenger are thinner than I'm used to on my HD. Thought I'd try these but after a few rides they were just too thick! It was like grabbing onto two rolls of toilet paper lol! No, it wasn't that bad, but my hands aren't big enough so it was a reach to grab the levers. So I cut them off and might try the Indian brand leather wraps... Good product, but just didn't work out for me.

To clear any pre- buy questions about Big Paw Grip Puppy. Installed on 2019 Harley Davidson Limited. Limited has factory heated hand grips. Did not have to cut or trim. Fit perfectly. Used small amount of diluted dish soap, warmed grips on bike and grip puppy's with hair dryer. A little effort but went on without too much effort.I have regular hand size, palm width 9in. Reg- large. Thickness of controls comfortable. I always ride with finger less leather riding gloves, or full cover gloves when cooler riding. Heated grips work as designed. Will keep factory rubber grips from wearing out.Great product.

Grip puppies are the best, they allow heat grips to easily warm your hands, they're re not as fat as the metal ones and have great grip.

Softens vibration. Softens about $19 dollars worth of vibration.

Was looking for a solution to prolonged vibration at high rpms on the interstate, and though these appear to be simple solution they are very effective as well. Have had them on my bike for two long trips both close to or a little over 1000 miles each and these performed beautifully. No numbness, no slippage or affect on performance. The only struggle was getting them on. I opted not to cut them since they could extend the length of my stock grips (2018 Honda shadow Aero 750). it would be nice if they included instructions on the methods you could use to install them however youtube provides many possibilities from compressed air, to soapy water. The Foam is very durable. I was concerned about ripping it while trying to get it on but as long as you don't use any pointed objects, it can handle the pulling and tugging to get it over the grips. I used zip ties along the length as separators in-between the foam and the grip as I installed. You can cut these grips down to smaller size if you need to, but I would take my time so you have an even clean edge. If you have a need to remove them , it's very easy to just roll them back off the end of the grip, no damage done to the puppies or your grip. My cramp buster also fits over the foam grip no problem. Great product and does the job.