Ensenior 12 Pack 6 Inch LED Recessed Ceiling Light, 5CCT, 1200LM 12W 120V

This recessed ceiling light exceeded my expectations! It gives off bright, even lighting without any flickering and instantly made the room look more modern. The installation was straightforward, and the slim design sits flush with the ceiling for a clean, professional finish. It’s energy-efficient, well-made, and provides excellent brightness for the space. I’m very pleased with this purchase and would definitely recommend it to anyone looking to upgrade their lighting.

These lights are great. The light is bright and clean. You can adjust the temperature level so you can install in a bedroom or an office. Set the temperature before you install them. You can change it afterwards but that means back on the ladder with more insulation falling in your face. Follow your local code as to which wire to get or hire an electrician. Easy install when you have attic access but not necessary. No attic access then get a good fish tape. I have them installed in bedroom, living room and office. Absolutely zero complaints. The builder wanted thousands for extra lighting but these and some diy effort cost a few hundred. I had the tools and had to purchase the three wire, Wago wire connectors, electrical tape and wire protectors. Or hire an electrician. I love these lights.

The Ensenior 12 Pack 6 Inch LED Recessed Ceiling Lights turned out to be a solid upgrade. The brightness is impressive — each light puts out strong, even illumination, and the adjustable 2700K–5000K settings make it easy to get the exact tone you want. The fitting is smooth and secure, and the build quality feels reliable. One of the best parts is the thin canless design. The low-profile housing makes installation easy in tight spaces, even under studs where traditional recessed cans just don’t fit. Overall, it’s a well-made, bright, and versatile lighting option that works great in almost any room. Very easy to adjust

They work well easy to install good price

Excellent lights - installed in my shed. Easy to wire for a clean look. You will need to buy a hole saw separately. The standard 6in hole saw I bought was just a touch too small - I had to notch out 2 sides of each hole to fit the brackets that hold the light in place. You can probably avoid that if you buy a hole saw specifically designed for wafer lights. (Also, most people will be working with drywall instead of plywood like me, so it would be more forgiving.)

Good product but lights flicker at some settings with dimmer-may be adjustable. Lights are very bright! Very good deal for the price

These Ensenior 6-inch LED recessed lights were incredibly easy to install, even with no existing cans. The slim, canless design made the process quick and clean, and everything fit perfectly. The lights are very bright at 1200 lumens and the 5CCT selector is a great feature—I could choose the exact color temperature I wanted for each room. They dim smoothly, look modern, and instantly upgraded the space. Great quality for the price and perfect for anyone wanting an easy lighting upgrade. Would definitely buy again.

The lights were very easy to install and they look great. I like the fact that they have the ability to change the color from 2700K-5000K. So far they work great and produce lots of light for my Man Cave.

Excellent et facile à installer

Bought these because I needed something I could install into existing drywall. Overall I'm very happy and would buy again, but do have a few recommendations and pro tips. - The unit is very thin, and will clear 1/2" drywall if you happen to be over a stud/truss. However, the tabs where the springs are are more like 3/4" high and so is the spot where the cable comes out. So if either of these hit the stud, it won't fit. I was able to make it work by removing the cable support, but only just. Would be better if the tabs were lower and the spring arm geometry changed to allow for truly flush install. Also relocate the cable to align with the tabs to increase the options. - I wish the unit was a bit wider. I was replacing 6" traditional pot lights and the holes were 6.25" so some of the holes were a bit wider and it was borderline. Still worked, but only just. Nice thing though was I didn't have to remove the full bracket assembly inside the ceiling, I was able to remove only the can assembly and leave the bracket in place. - Junction box is really small, I had max of two romex/loomex 14/2 wires daisy chaining through these and it was tight. If you had 3, it would be very difficult and I would say, might not meet Canadian code. - Push terminals are nice, make sure you strip to the right length because if too long you have exposed conductors, too short improper contact. Also as far as I can tell, there is no way easily to release these if you screw up. I accidentally terminated a neutral into the hot and had to jam a pick in beside the wire to release the tab, it was a pita. One suggestion would be for an improvement is to replace these with the flip up tab type like WAGO's. - Annoying that there is no strain relief/grommet provided. I suggest getting 1/2" plastic snap in type on amazon. They're half the price of the hardware store, but get one for each wire, don't try fit two romex in each even if it says you can. Its a pita. - The color switch is amazing, works great. I ended up deciding I wanted a warmer white and was able to pull all 12 lights down and adjust in about 1 min each. Pro tip here, mind the spring tabs pulling the light down. Hurt like hell if the snap your finger and worse if they snap back, the metal wire can chip the bezel, so just be gentle and get a hold of it as you pull it out. Happened to me, but fortunately it was next to a wall, so was able to turn the light so it wasn't visible. - I recommend getting a larger pack than you need, so you have spares. LED's never last even close to their theoretical lifespan and 2 years from now, these might not be available with the same look/color temp. I needed 12 and I wish I bought the 16 pack, now I'm paying extra for a smaller pack. - Last thing, I bought a 6-1/8" hole saw on amazon ($19) for the holes I had to cut and it worked great for drywall and totally worth it for the price. I suggest marking it with the thickness of the drywall so to reduce the chances of hitting something you didn't know was there by cutting too deep.

Highly recommended. 3 months post installation and my wife, the chief product reviewer in our house, and I continue to be impressed with these lights, so much so that I will be buying them again for my upcoming basement reno. Light intensity ranges from a very low level, without any flickering or hum at all using a Lutron Maestro MACL-153M dimmer, up to very bright. The ability to change the color tone (we chose 4000K) helped to adjust to the ambiance of our kitchen decor. The one critique I had regarding the size of the wiring box is minor in comparison to the performance of these lights. Ensenior reached out to me because of this issue and I found them to be genuinely interested in customer feedback. 5 Stars also to Ensenior. Overall: Very satisfied! Pros: Very bright light with selectable LED coloration; fits tight to ceiling (note - foam gasket is not necessary if not installing in a damp environment); works with my existing Lutron Maestro MACL-153M dimmer; powered 11 lights; relatively easy to install* and great overall. Cons: *The box is quite small, especially if you are daisy chaining the lights as would be the case in most installations in Canada using 14GA wiring. I would suggest that the box could be 2 or 3 inches longer to accommodate the above.

I won't go with any other recessed pot light. The ease of installation. Five setting to adjust the brightness of the light. Used with a recommended dimmer there is no flicker or noise. They come packaged nicely so the lights were all in good condition on arrival. All pros and no cons so I would highly recommend.

I love these things (12 pack 4Inch LED Recessed Slim Pot Light with Junction Box) 5 selectable color temperatures means you can select warm white to harsh white to match the room, dimmable and don't make any buzzing noise (but that might depend on your dimmer). So slim they install anywhere even if there is a joist right where you want to put one, these are getting installed all over the place in my house!! A couple of things that could make them even better - 1. If the junction box was just an inch bigger it would make installation so much easier. 2. Make sure the wire is properly seated in the wire splice block before cramming it into the box coz the wires can pop out - even better replace them with Wago lever locks which is what I did. 3. Why don't they chuck in some 1/2 inch plastic romex cable connectors? - for a couple of cents each it would just be a nice touch. 4. Buy extras / spares - they're cheap so grab a few spares for if/when some fail in case you can't get them anymore in the future. 5. Get a good hole cutter and you won't regret it, I got the Milwaukee adjustable hole saw (C$35) and it's worked really well so far (about 40 nice clean holes). 6. Don't skimp on the number you plan to install, with 8ft ceilings if you don't install enough you can end up with dark spots in your room, but this is the same with any pot lights so read up about standard spacing for pot light installations. 7. Buy a good dimmer if you want to dim them, if you get a cheap crap dimmer switch you will regret it. Most of my comments above are just tips / advice and not criticizing the product itself, becuase these LED pot lights are fantastic.