KUNCANSAE to Ring Terminal Cable - O Ring Eyelet Terminal Harness Quick Connect/Disconnect Ring Terminal Assembly Extension Charge Cord

The media could not be loaded. I purchased this to complete a simpler on-shore charging system for my boat, the kit will work for any situation where you need to periodically charge or maintain 12volt batteries.These ring terminal connectors worked exactly as expected. The terminals were the ideal size to fit on the posts of my deep cycle batteries. The included fuse holders insure that the wire will not melt if for some reason too much power is pushed across the wire. The SAE connectors on the other end provide great flexibility for connecting to other devices. The SAE connectors have attached caps that allow covering the connector completely to insure it will not short out when not in use.I can use this as I intended for charging, or I can connect accessories directly to the battery using the SAE connector, assuming they draw less than 10 amps of power. It also makes a convenient point to test battery charge with a volt-meter if necessary.The charging solution I am using this with includes two different charging sources, a Suaoki 60Watt solar and a Noco Genius G3500 Smart Charger. Both are great and provide a similar amount of power to the batteries. The solar charger does not work so well at night though, and the wall charger does not work when out camping on the boat.Suaoki 60Watt Solarhttp://amzn.to/2w1ylpKNoco Genius G3500http://amzn.to/2gan697Using the Suaoki solar charger requires the using of a solar charge controller for safety. The Suaoki can be directly connected to the battery, but then the voltage must be monitored as it can overcharge your batteries and lead to premature failure or worse. I am using the Instapark PWM charge controller for this task and it is a perfect match to the system.http://amzn.to/2xg7pAWThe NOCO Genius uses properietary connectors and while it comes with a few different options, none of them made it compatible with my requirements. I ordered the NOCO to SAE adapter and now it connects to a standard SAE plug and works well, interchangably with the Solar charger.http://amzn.to/2wrOxl0In order to add flexibility in placing the solar panel or connecting the NOCO charger, I added an SAE extension. Essentially this is a 12V extension cord. Any SAE to SAE cable will work provided it has sufficient gauge(AWG). For a 15ft length this should be at least 12AWG with 10AWG or even 8AWG being better. For a 5ft length 16AWG or 14AWG will be acceptable, of course 12,10 or 8 still better. Anything smaller less than those maxiums will degrade the charging capacity as it will cause an significant voltage drop. Here are a couple alternatives that look good.Kuncan 12ft SAE to SAEhttp://amzn.to/2iuIzduTetra-Teknica MotoBasic 10AWG 3 Feet, 2 per Packhttp://amzn.to/2g7VT6SI used two ring terminal to SAE adapters, one for each battery, as the aligator clamps were problematic and not particularly reliable. The aligator clamps meant that I had to climb into the compartment where the batteries are stored in the boat and almost always insured a good bump on the head. Sometimes I would come back the next morning to find one had fallen off. Using ring terminals insures a secure connection to the battery and allows me to quickly connect/disconnect without bumping my head. I used the Tetra-Teknica MotoBasics 16 gauge 2 feet 10A fused 2 pack for my solution.http://amzn.to/2w89HlTIn order to charge the two batteries in parallel, I needed to add an SAE Y adapter. The OptiMate Y-splitter worked nicely. I disconnect it when not charging as I do not want power accidentally pulled accross this connection if the boat is using a single battery. I am looking for a solution, a diode that will allow me to keep this connected permanently without that risk.http://amzn.to/2w1wjG0The system is working well and keeping my batteries topped off between outings without a problem.

Straight forward product, works as described A+

Been using one of these for about 5 years on my ATV to power sprayer tank. Holding up well, quality seems better than typical chinese junk.

Product came as described. Works as desired. Only reason I didn't give it 5 stars- the protective cap (for when not in use) is made of plastic. The first cold spell we got in central Wisconsin, it snapped off. Next time I'll look for one with a rubber cap.

im really happy with this, i sleep with it.

Works as advertised. Allows me to quickly connect my battery charger to my car with safety. The 10 Amp fuse is easily replaced.

Excellent wiring. Works well and made very well,I ordered extras.

and better than the supplier used with the original.

Tiene el largo suficiente para instalarlo en cualquier lugar y el cable lo suficiente grueso para no romperse , tiene buena calidad igual los conectores

Bought this as an add-on to a previous one which wasn't quite long enough. Fitted in well with the original and is certainly very robust and waterproof. It is used outside and there have been no issues. Very good.

Bonne qualité, fonctionne très bien sur ma moto.Merci

Accessorio ben fatto, ottimi materiali. Valutate bene gli spazi che avete a disposizione per installarlo su una moto perché il fusibile ingombra ed è posizionato troppo vicino all'occhiello che va al morsetto, su una Harley Street Bob ho faticato non poco per inventarmi un percorso comodo. La presa SAE è molto comoda, io l'ho posizionata sotto la sella e ci collego una presa USB che ho sul manubrio all'occorrenza.

El cable tiene una calidad excelente, con terminales bien crimpados, portafusibles y tapón en el conector SAE para que no entre suciedad cuando circulas con la moto. La sección del cable es de casi 1,5mm cuadrados (16 AWG), lo que garantiza un adecuado paso de corriente de carga (el fusible es de 10A).Su longitud (61cm) permite conectarlo a los bornes de la batería y dejarlo escondido entre el chasis para poder conectarlo al cargador sin desmontar tapas ni otras complicaciones parecidas.