ASGHand Weapon Bag dan Wesson 8.5 x 23 x 46 Handgun Case - Black, One Size

OMG..If you want to show off your new Dan Wesson revolver (mine's a 715 4" pellet), this is the case to get. Laser cut-outs for the gun and accessories (gas x 2, speed loader x 2 and rail), it both shows off the gun to perfection and protects it superbly. It's extremely well made with good hinges and twin slide locks (no space for a padlock but you can use a cabled one wrapped around the carry handle) and is made from a robust plastic material that won't shatter if dropped.Very highly recommendedUPDATE!!!========I've just noticed that there are a couple of holes, one each side of the 2 closing catches for padlocks. They would have to be fairly small as the holes are only about 3mm in diameter. But it's better than nothing and will keep unwanted hands off your prized possession

Nice case with perfect cut outs, and removable foam inserts for the following:1 x Dan Wesson 715 Co2 gun (up to 8")2 x 12G Co2 cartridges2 x Speed loaders12 x shell's/pellet cartridgesHas slide latches on either side of the handle to fasten case shut, which hold relatively fast. And the handle could also take a cable combination lock (requirement to keep gun fastened and unloaded/separated from ammunition by uk law). Sadly the handle is a little too big for padlocks but a good quality cable lock does the job fine.

I bought this for my PCP pistol, absolutely great.

I really like the Dan Wesson Revolvers from ASG (I have 4 in different sizes and models), so it would follow that I would have tried at least one of these cases (again I have 4, one for each of my revolvers)These are made from nice quality textured black plastic and have the Dan Wesson Firearms logo on the front.There are 2 slide closures, one either side of the handle which work well. There are 2 holes on the slide closures so that you can fit padlocks or similar to prevent them from being opened. However the padlocks simply block the slides and don't pass through both sides of the case, meaning that if you can pull off the sliding pieces of the closure system then the case can still be opened even with the padlocks in place. The slides could be pulled off by hand by someone of modest strength making this a case which cannot boast to be overly secure although it will keep out smaller children when used with padlocks.I also wish the outside of the case had a facility to add a label or something similar. There are I think at least 7 different variants of the ASG Dan Wesson revolvers and so it is feasible that some one (like me) would have more than one of these cases, and knowing which gun is in which box without a label some sort is difficult. I have added some home made labels to mine, but it would be nice if the labelling system was part of the case.The case comes with internal foam, with cut outs for the 8" original version ASG Dan Wesson revolver, 2-4 gas canisters, 2 speed loaders and the extra rails which come with some versions of the revolvers.The gun cut out is good. It is cut for the original frame design but 715 versions will also fit nicely (but not perfectly). Revolvers with barrels shorter than 8" will also need some of the foam at the front of the barrel section cut off and replaced in the hole to reduce the length of the barrel slot in the case to suit the length of barrel your revolver has.The gas canister holes are designed to take 2 bottles, however I found that the cut outs on these go right through all the foam. So after pulling out the 2 top sections, the lower sections can also be removed (they are glued but pull out intact with minimal force). with the upper and lower foam cut out removed you can now store 2 CO2 canisters in each slot for a total of 4 canisters.The cutouts for the speed loaders are just as you would imagine, and take loaded or empty speed loaders of the type supplied with the revolvers.Even with these cutouts all removed there is still some foam left that can be cut out for extra accessories.These cases are not perfect by any means, but they are perfectly adequate for the ASG Dan Wesson revolvers they are designed to house. And if you have a Dan Wesson Revolver what could be cooler that a case that has the Dan Wesson logo on it too.

Ideal storage for my 357 Magnum

Great airsoft pistol carrying case, great quality, lots of thought and nice touches!

Great product extremely well made with laser cut outs for gun-speed loaders and spare shells I’ve added more cut outs to accommodate my other stuffA very robust and well made case would recommend

This is my second dan wesson case that I've purchased. These cases are great, so I would highly recommend these. The only issue is that the price has increased.