Lian Li Lancool 216 RGB Controller White

Easy install behind the front frame on the case (which simply pops off). Nice mesh that should really help keep a good bit of dust from pulling into the case. Doesn't get in the way of any cable management, and the color is as shown in the pictures. Functionality wise, I am happy with this purchase! Will dim the brightness of your case fans as you see them through it of course.

First and foremost I got this to replace the empty piece of plastic that is there on this case and to provide me with an extra set of USB ports. At first I did not care about the RGB control not being done by the system but now it makes it makes it much nicer as I don't have to rely on a piece of software that may or may not work for the motherboard and operating system your using. Now granted the option for lighting control is not as nice as the software version but you still can have it be done by the controller or software, all you have to do is hit the right sequence to tell the controller on this that the software on the PC is in controll. The nice thing is by default it is already set up that way, so you don't have to change anything if you don't want too after installing this. The install was pretty easy, but you may need to get an adapter for the 19 pin USB plug to USB 2.0 port if the one on your motherboard is already being used by the one with the power and reset button or get a adapter for that one to the new USB 3.2 gen2 instead and plug this into the 19 pin port. I'm using it as USB 2.0 ports as it's only going to be for keyboard and mouse so fast enough for that.

The Lian Li ARGB control is not compatible with Asus Aura Sync. The fan speed controls can not assigning fans to specific temperature sensors. It fits perfectly and the extra USB ports are why I buy it. It would be nice if 1 port was a type "C" port.

Firstly, I couldn’t find the answer hardly anywhere online but this WILL control the RGB for the rest of your fans, given they are down line of this controller. Also to answer a few common questions; 1. As stated above, this will control other RGB fans in your case, whether they’re lian li or not. But they need to be run down line of the controller. The diagrams can be a bit confusing so here’s how I did it. First connect the female ended cable to your mobo’s 3-pin RGB header. This controller needs to be the first thing connected to control the fans. Next run the male end to the fan hub’s (the one preinstalled on the back of the case) female connector. This will allow the fan controller to change the RGB lighting of all the case fans given they’re connected to the hub. You can also daisy chain them from the controller itself. If the bottom two buttons aren’t working, check these connections. 2. I saw some people say they can’t change the color of the ring around the front case fans. The controller comes out of the box with them synced to the fans. To un-sync them you will need to press key 1&2 together for 3 seconds. This will un-sync and sync the fan and rim color and make the top two buttons work. Be careful which keys you press since I believe pressing keys 3&4 together for 3 seconds will pass control to your mobo’s software, just press them again to undo that. 3. For the USB cable, you can get a splitter that will have two female ends that you can plug both the cables from this and the cables from the top up panel into, I haven’t tried it myself as I don’t need the usb inputs, but it’s an option. Though I’d recommend doing some research on your mobo and the cable itself. 4. As far as the usb cables go they are stiff and a bit difficult to route, but it just takes a little work to get them there. The directions are a little vague with how to route them, it took some trial and error but I learned you need to route them on the outside of the cage that holds the fans, and they will curve down and sort of under the lower fan in between the two mounts where the screws would go, on the side of the fan, then going through the gap at the bottom. It is a little worrisome getting them to bend at that angle but the cables are sturdy. 5. To my knowledge it will not work with software such as L-connect or open-RGB. As for my thoughts overall, I think it’s built well, and works well. I wish the RGB cables were just a couple inch or two longer though. It’s worked well for me and has some nice patterns it can display. I do think this should have come with the case, even if you had to pay a bit extra. There isn’t a lot of info on this controller so I hope this helps!

Fits perfect, unobtrusive, easy to install and works well. It should have come with the case though, the fine mesh holes in the case really don't do a very good job of filtering dust, no matter how in style they are right now.

Item was easy to install in the computer case.

Die Anleitung war super simpel und einfach gestaltet, das Produkt ist hochwertig und passt perfekt in meinen Pc, leider war mein Mainboard nicht kompatibel für 2 weitere 3.0 USB Ports, darum kaufte ich mir noch einen Adapter aber glaube neuere Mainboards haben das Problem nicht mehr. Dennoch einfache Installation und auch einfache Bedienung kann ich jedem Empfehlen für das Case, da man die volle RGB pracht erhält. Ist nur blöd das dann keine Steuerung übers Mainboard mehr möglich ist.

純正オプションなので、もちろんケースにジャストフィットです。 ケース前面にUSBポートを増設できるので便利です。

Perfecto funcionando y conectado facil y como un guante como todo lo que fabrica esta marca.

Makkelijke installatie en werkt perfect! Ik kan er verder niks anders op aanmerken. Ik ben blij dat ik het heb gekocht.

A little difficult to install due to the stiff wires. Cool lighting effect, clear controls. BUT it can only control two fans