Draw-Tite 75579 Class 3 Trailer Hitch, 2 Inch Square Receiver, Compatible with Chrysler Town & Country, Dodge Grand Caravan, RAM C/V and Volkswagen Routan (please verify VEHICLE APPLICTION)

Fit my van perfectly. Easy to install. Great quality. All hardware necessary was included. Good value for money.

Easy to install. No issues. Heavy duty. On a Dodge Caravan, there is one bolt that is trick to get to, but they provided a wire tool to install the bolt properly. No drilling or cutting required. I see Amazon has marked this as frequently returned item, but I would surmise that this due to the fact that you actually have to install this item. It is not a pop on, click in place item. You need to lower your exhaust, bolt this in place and re-install the exhaust back up into place. First time around, it should take you about 90 minutes or so.

Easy to install and fitted literally perfect. I used a Dewalt 20v impact to take out the bolts and to reinstall them. If you use a regular wrench, it will take you a while to do the install. (Careful with your wrists). The driver side was very easy to remove the bolts and to reinstall them. The passenger side however has a muffler and you will need to remove two muffler bolts hangers in two different locations, so that way muffler can nudge to the side a little bit to get to the bolts. I suggest you do the muffler side first so that way you can put the hitch onto the muffler (you have to angle the hitch in) so the muffler can hold the hitch in place with no bolts. Then you raise the driver side and insert the bolts finger tighten. Next you go to the passenger side and start to put the bolts on there as well. Once all the bolts are in place then you can tighten the hitch bolts in. Once all the hitch bolt are secured reinstall the muffler bolts back in. I also used my ramps to raise the back of the van which helped insert the passenger side through the muffler. It is heavy so ask for help if you need it. Took me less than 30 min.

Product is great quality is fantastic. The UPS driver struggled with this awkwardly shaped heavy object for delivery. Couple suggestions before you buy this. Get a 2-3ft breaker bar from harbor freight it will make your life easy. I could not have done this without this since the bolts on my 2015 chrysler T&C were rusted over. Rhino ramps and wheel chocks made this super easy to install along with an extra set of hands. I'm overally cautious so i also used jack stands. Overall took maybe 30 minutes from start to finish to install. I also use Remove 7 total bolts. Put on hitch. Then put the 7 bolts back. Hitch is just heavy and awkward. I used a floor jack/jack stands to help position the hitch for install.

I have worked with Draw Tite and other hitch products Over a span of 30 years and installed them when I was younger professionally. They are asy to install if you have the right tools, if not, leave it to someone that does. At a minimum you need a long breaker bar or air tools to remove and install the bolts in the frame of the car. I did not have A breaker bar or air tools but did not expect the issues I ran into to install it. One bolt was cross threaded and it was an exhausting chore to remove it. This hitch did not require any drilling but many do, make sure you check before ordering so you know what to expect. You also need at least 2 people since the Chrysler town and country has a bumper that goes in the frame which the bolts go into. You have to align all of the parts to get the bolts started. Make sure you get them all started before tightening them or you may have difficulty getting the other bolts started. Due to the issues with the cross threaded bolt and getting them all started without having to do a lot of loosening and tightening, it took about an hour and a half to install it. As for the receiver itself, Draw tite has always made a great product and I’m sure this hitch will provide many years of service. Check all bolts annually and it should last the life of your vehicle.

This hitch, despite what some of the other reviews state, is an easy to bolt on hitch that required no special skills to install. It does NOT come with hardware, which some reviewers complained about but it does not NEED any since the hitch utilizes existing bolts/hardware. The instructions are well laid out and easy to understand if you actually need them (I did not). One note to ease installation. The muffler needs to be unbolted from it's hanger, which is easy enough however despite that the fact that muffler is unbolted, the operating room above it to access a mounting bolt is quite small. Unbolting will require the necessary socket but also realistically requires a universal joint attached at the point of the socket with a 6 inch extension. To make the job easier, since there is no swing room for a wrench, an impact gun with a universal joint will make life far easier for this install, specifically for the bolt above the muffler (that's what i used) but it's not mandatory. Also, this hitch is compatible with "stow and go" seating, which is on my van (2012 dodge grand caravan). This is a two man install only because it's quite heavy and wide. A floor jack will suffice if you don't have a second set of hands to hold the hitch up as you perform the install. Just figured I would offer my two cents.

Easy enough to install (moving the exhaust was annoying but part of that process). Appears to be very sturdy and fits great. I used a cargo hauler with about 400lbs on it for 800 miles. I had zero issues with the hitch and happy to finally have one installed! Biggest recommendation is to make sure you have the right tools. I had to purchase a breaker bar wrench as it was not possible to remove existing bolts without it. Very satisfied!

Held up 4000 pounds