Peak Design Micro Clutch I-Plate Camera Hand Strap, For Mirrorless Cameras, Low-Profile Finger Loop, Battery Access, ARCA-Compatible Baseplate, Secure and Comfortable, Camera Straps for Photographers

It’s super sturdy, really convenient, and you can tell it was designed with real users in mind. The triangular anchor didn’t quite fit Ricoh and caused a small scratch, but I don’t mind it. I ended up attaching it together with my wrist strap, and it still works perfectly. I’m really happy with it!

I generally love Peak Design's products but this might be the first where I initially wondered if it would work for me. Overall I like the concept and have been waiting for a minimal strap like this. The bottom plate is quite good. The magnets, built-in tool, and overall design is well thought out. The only thing I could wish for from this part would have been to make the plate itself Arca-Swiss compatible (though I suppose that would make the plate much fatter than it is), and to improve the tool so you can use it vertically on the long end. It's a bit awkward to use, as the long end is angled, and the short end is a tad too short and it kind of catches on the tripod plate. The thing I found initially disappointing is the strap. At first, I couldn't set it up to where it felt comfortable. I tried setting it at different settings and found on the tight settings, the little plastic stud that secures the strap dug into my finger. Also when trying two finger mode with it somewhat loose, the padding was on the top end by the lug, and the bottom part of the strap had no padding, which dug into my hand. I removed the stud from the padding and adjusted it to be pretty tight, and that seemed to have fixed my comfort issues. This comfort of this strap is probably really dependent on the size of your hand and the location of the camera's eyelet. I bought this to use with my Olympus E-M5 Mark III, and maybe I'll get the L-Plate version for my OM-1.

UPDATE: Been using this for a while now along with the Camera Capture Clip from Peak. I've found it really convenient for casual and street photography. In addition to the short strap, I also found the built in tool to loosen the base plate is difficult to access on the Zfc with larger lenses or adapters. It really should have been mounted on the back of the plate intead of the front. Again - neither are show stoppers . I also have a Peak Design travel tripod, so just leave the mount attached to the baseplate. Just got this for my Nikon Z fc. I like the setup. Very well designed. Especially the attached tool to loosen the attachment screw. And, as advertised, it is a really convenient way to carry the camera when you're walking around taking random shots. The one issue I have is the length of the strap. If you have larger hands, it's may be a little tight. For the Zfc it makes access to the front control wheel a little awkward. Not a show stopper. Just be nice if it was a bit longer. UPDATE: I moved the attachment plate so it extends about 1/2 inch past the right side of the camera. It now works perfectly and the change doesn't interfere with using/carrying the camera. I use the Z fc for "mobile" photography - street photography, landscapes, people/places/things. and am finding this much more convenient than the standard neck strap.

It is high quality, but it does not work with my Leica M6. The reason I purchased it is that the M bodies are not very ergonomic. M- cameras screw to put on the baseplate is located on the far right not in the middle like other cameras, so when you use this it sticks out about half an inch and makes holding the camera and look bad.

Its solid, works well. I really appreciate the strength of the magnet holding the tightening tool, thats a brilliant touch.

The plate does not secure well due to the single screw not having enough bite inside the slot and a pivot point it creates with the edge where the strap is attached. Also, it needs the mounting hole to be in the center of the camera base, which is not the case for s9 or om-3 I tried it on, and as the result, a part of the plate sticks out in the front. The plate also blocks the battery door. Sadly, the strap cannot be detached from the plate, otherwise one could use it with a different plate or grip that has a strap slot at the bottom. The fastening mechanism is hard to use, and the strap with those holes doesn't seem very durable at all.

I did not like this product and ended up returning it. I don’t like the fact I was unable to access my batteries while it was installed, and it’s not something that’s easily remove to resolve that issue. It’s a pain every time I needed to swap batteries and hurt my fingers. The quality of the leather and strap just felt poor.

This hand strap is beautifully designed and fits the Leica D-Lux 8 perfectly. Provides a secure grip. Base plate is solid.

Bought mine at the discounted price and totally feel the gripping of my camera in a higher level!

Good for small Frame A7C a little fiddling to get fit and with replacing battery but good quality

Bir süre kullandıktan sonra yine eski dost peak design wrist cuff a döndüm ama bu 5 yıldızı hak etmeyeceği anlamı taşımaz :) X100 VI Fujifilm kameramda micro clutch ile cuff wrist arasında dönüşümlü kullanmak için aldım. Memnunum

コンパクトなクラッチなので小さいカメラに使いたいところだが、小さいカメラの多くが三脚ネジの位置が変なところにあるのがおおく、カメラ全面にプレートがはみ出す可能性が高いのがすごく残念 fuji x100vi用に買ったのだが見た目がダサすぎて使用を諦めた 現在はnikon zfで使用しているがほんの少しはみ出しているが妥協できるレベルで、しっかりホールド出来て満足している

The Peak Design Micro Clutch I-Plate hand strap is an excellent addition to my mirrorless camera setup. I've actually purchased two of them because they fit so well. Initially, it does take a bit of time to adjust and get everything set up perfectly. However, once you’ve done it a couple of times, it becomes second nature. One thing to note is that for most cameras, you will need to remove the plate to access the battery. While this might seem inconvenient at first, it really isn’t an issue and doesn’t take long once you get the hang of it. It’s a small trade-off for the added comfort and support the strap provides. It’s also worth mentioning that this strap will not work with the older capture clips, so keep that in mind if you’re using an older setup. Despite this, I’ve found the strap to be incredibly comfortable and it looks great on the camera. The design is sleek and it adds that bit more support, which is especially useful during longer shooting sessions. Overall, the Peak Design Micro Clutch I-Plate hand strap is a fantastic product. It provides excellent support, looks stylish, and once you’re familiar with its quirks, it becomes an invaluable part of your camera gear. I highly recommend it to anyone looking to add comfort and stability to their mirrorless camera experience.