FOLAI Copper Pipe Expander - Universal Hand Tool for Refrigeration & Copper Pipe Swaging - 1/4", "5/16", "3/8", "1/2", "5/8", "3/4", "7/8" inch Tube Expander

Great tool works perfectly

Awesome product. Used on my heater core copper lines out of the firewall in my civic!Worked great!

The tool is growing on me. You have to take your time and be very patient. It’s not an instant thing practice makes perfect. It looks very durable and it feels very durable and quality built and I sure like the idea but you just have to go out it really slowly and keep turning your pipe.

I used this to make a bushing for a door lock fit. The insert that goes into the door which the bolt slides in and out of. It somehow backed out of door when door was closed and got a flat spot making lock inoperable.This tool was cheaper than a replacement bushing and bolt set so figured I'd give it a try. Put the bushing flat spot over one half of the curved bit and applied pressure, the sheet metal of the bolt bushing straightened right back out to round and fixed the door problem. So, it paid for itself not he first use and if the bushing comes loose again, I have a fix for it.I imagine it would work similar on copper ope though you'd need to rotate the pope 3 or 4 times and squeeze to ensure it's uniformly rounded out

I had to return this item once because the halves of the die were so badly aligned. The second unit was a little better and allowed serviceable expansion of soft copper tubing. The depth of the expansion is a little on the shallow side, and it takes some practice to not over expand the tubing to get a usable connection that will flow together. I only tried this with small diameter tubing, but it sure beats hammer and die. I can imaging the handles may be a little short to get adequate leverage on the largest diameter tubes this tool will support.One tip when using this is to get the tube to line up just shy of the beginning of the taper to the next size up. The hinge will cause the dies to slightly misalign and will overexpand if the taper hits the end of the tubing. Keeping the end of the tube shy of the taper results in less cut off the end and try again, most of the time.

I have used this a few times now with great success. Yes, you must rotate the pipe while swaging to maintain a round cross-sectional shape. And, those who complain about split pipe are probably attemtpting to swage hardened (tempered) copper tubing used for water lines. Swaging must be done on soft copper. An end (say ~ 2 inches) of hardened copper can be annealed (softened) by heating with an ordinary propane torch to a cherry red color and then quenching in water. Be aware that "working" copper (via bending, hammering, swaging, etc. also "work hardens" (tempers) the material. However, merely swaging the end of a copper tube does not constitute enough "work hardening" to cause breakage. If the tube is rigid, as for water, it has been hardened and will need to be annealed before swaging to prevent splitting while swaging. That is not a big deal; just heat the end to be swaged with an ordinary propane torch and then dip in room temperature water to quench. After that process, the end to be swaged will be "annealed" and soft enough to swage. After swaging it will be ready to solder. For those unable to finesse the "rotating while expanding" part of the process to achieve an acceptably concentric tube end, I suggest using a tube flaring and swaging kit, many such kits also available here on Amazon. (I have one from Wostore that is very nice, is economical, and does both swaging and flaring. In that case, you lock your tubing into an appropriately-sized hole in a steel swaging bar, install an appropriate-sized swaging die into a swivel connector on a steel yoke (yoke is a type of clamp that locks onto the swaging bar) and then turn a handle to screw the swaging die into the inside diameter of the copper tubing to expand it. The latter method obviously takes many more steps and is thus much slower than using the swaging tool of this listing, but the die makes a perfectly symmetrical expansion without artistic finesse from the user. I believe that most of the problems expressed by frustrated reviewees stem from attempting to swage tempered (hardened) copper without annealing. The video by the seller is not helpul at all and probably adds to the confusion. He appears to be doing the process at breakneck speed to impress would-be buyers with how quickly swaging can be done using his tool. However, the undesirable result is that one can hardly see that he is rotating the tube while he works to maintain a symmetrical expansion. He probably receives many returns as a result, when a purchaser simply inserts the tool into a piece of tubing, squeezes the handle and is disappointed with the asymmetrical result. If the tubing is tempered, both an asymmetrical and split cross section can result. So much confusion due to poor communication, so little time...

I tested this guy out on some scrap 3/4 copper. It works great. I had to switch back and forth from one side to the other as I built up to the final size for my bell shape. I kept rotating as I went. I found it very easy to use. Yes, it will take a bit longer than the expensive hydraulic units that an HVACR pro would use, but it seems like a very well made tool and I made a nice tight-fitting little swage/bell in my test. Looking forward to putting it to work on my next brazing project.

I do a lot of work with irrigation systems as well as tubing associated with compressed air, fuel lines on motors, water hoses, etc. This thing is worth its weight in gold to me, even though I've never used it on copper tubing. I've only used it on vinyl, rubber, and other flexible materials. It gets me out of jams that used to seem hopeless. I was just fixing several breaks in ¼ inch drip lines using old, stiff replacement tubing. I didn't think the tool would go that small, but it did, and a hellish task became a walk in the park. I've had it now for a couple of years and wouldn't want to be without it. My son owns and operates a car-repair business. I gave him one, and he says it regularly helps them out at the shop. There are multiple brands for these things. This is the brand I bought, and I highly, highly recommend it.