Question 1

Does the can tap that is included work for R134a small cans?

Accepted Answer

Yes. It worked just fine. The only problem I had with it was getting the leftover amount in the second can to seal and not bleed out once I removed the hose. I took the protective vent cap off the yellow hose manifold air vent and screwed it on with some teflon tape on the thread to seal and it appears to be holding.  JB

Question 2

Does the 134a can tap work for self-sealing cans or just piercing-style cans?

Accepted Answer

NO!  Despite the vendor's claim, the tap supplied is for old-style piercing cans only.  
It does NOT work with self-sealing cans, only with piercing style.

Yes I fully understand how it works - for this cam-locking adapter you have to partially unscrew the cam plate, fasten the cam to the can, screw the adapter in so it contacts the can top, un-attach the cam, screw the adapter maybe 1/2 turn further into the cam plate to make sure it will seal, re-attach the cam plate to the can, then screw the valve in.  It would not operate the self-sealing can.

Don't bother with the cheap $3 blue plastic can-top adapters, either.  My closest parts store had a brass adapter from "sure-built" (Made in China, ~$7) that did work.  Plan on spending that extra $7.  
ALSO plan on another $10 to replace the hose end gaskets with 1/4"  Hose Gaskets  e.g. https://www.amazon.com/Yellow-Jacket-Quick-Coupler-Gaskets/dp/B00E549YWW/  -these hoses come loose if you just look at them the wrong way.  I HOPE the new gaskets will minimize that.  Right now I have fluorescent dye leaked al over my compressor, which means I can't tell if there's a leak in the shaft seal until I clean all that shit off, and my compressor is hard to reach.

Question 3

Anyone was able to replace the seals on the female connections? They usually go bad quickly... Any particular brand?

Accepted Answer

Yup... replaced them as soon as I saw them. Amazon sells a couple of types-I have used the Green seals and their OK but I like to use the Yellow Jacket black seals. they seem to wear the best. You can also check your locale auto parts store, they should carry one of the name brands.

Hope this helps.

Question 4

what is the trick to making the can tap work with self sealing cans?  I could never get any freon to come out.

Accepted Answer

If you follow this and it still does not work-the tap may be defective.
1-Back off both the tap body and the valve.
2-Mount tap on can, and screw tap body down till it contacts the top of the can and tighten 1 turn. This should snug up the can and tap- if not - tighten a 1/2-1full turn more.
3-Now close the valve handle while holding the can and tap body.     
 *NOTICE* Wear gloves and eye protection!   FREON AT ROOM TEMP IS ABOUT MINUS -60.DEG AND WILL CAUSE FREEZE BURNS ON CONTACT!!!   
4-Once you close the valve fully it should pierce the can top.

Brand	Orion Motor Tech
Material	Brass, Aluminum, PVC, Durable Plastic
Item dimensions L x W x H	12.6 x 11.81 x 3.74 inches
Item Weight	7.85 Pounds
Screen Size	3.74 Inches
Manufacturer	Orion Motor Tech
Item Weight	7.85 pounds
Product Dimensions	12.6 x 11.81 x 3.74 inches
Country of Origin	China
Item model number	5864299654
Is Discontinued By Manufacturer	No
Manufacturer Part Number	OMTDMG171

OrionMotorTech 4 Way AC Diagnostic Manifold Gauge Set for Freon Charging and Vacuum Pump Evacuation, Fits R134A R410A and R22 Refrigerants, with 5FT Hose, 3 ACME Tank Adapters, Adjustable Couplers and

Details

Description

Specifications

Have a Question? See What Others Asked

Common Questions