Official Creality Ender 3 3D Printer Fully Open Source with Resume Printing Function DIY Printers Build Volulme 8.66x8.66x9.84 inch

EDIT: Update 8-9-18 The company reached out to me and offered to replace some of the parts that I was having trouble with. I've changed the review from 3 stars to 5 starts for excellent customer service. Original review: I wanted so bad for this printer to be the best entry level printer on the market. Key word: wanted. I purchased this at the end of June as a small step into the 3D printing arena. With the success of the CR-10 (made by the same company as the Ender 3), I felt that the Ender 3 was a wonderful option if you didn't have a need for the large print space that the CR-10 has and were on an entry level budget. That's not to say that the Ender 3 has a small print space. For the price range, this has one of the largest. Assembly of the Ender 3 can definitely test your patience. If everything is not lined up just perfectly when you tighten all of the screws down, your end result will be a wobbly 3D printer. (FYI, the packaging that the printer came in helps resolve this issue if you set the printer on top of it.) Some of the first prints that I did weren't difficult to print as I wanted to ease into all of the features this has. Here's a quick list of my pros and cons: Pros: - Ease of use - The menus are easy to find and understand. It's incredibly simple to put your stl file on the micro SD card and start printing. While the placement of where the SD card goes in is a bit of a headache, you can get used to it over time. - Bed surface - I like the surface of the heated bed as it really grabs the plastic and it's one less thing you have to worry about (i.e. putting glue on the bed). Some times, it can grab the print a little too well and it makes removal quiet interesting. Cons: - Quality - In general, overall quality of the printer is lacking, but that just may be par for the price point. Prints can greatly vary from "it looks fine" to "what happened?" While I admit some of this may be my fault and inexperience with Cura, I've found that printing the same successful print can also give different results without any of the files being changed. Another quality issue were the rollers either being too tight or too loose from the factory. While some experienced 3D printing people know to look for this, someone who is taking this printer as their first step may not know how this will affect their prints. - Heated bed - Again, I like the build surface of the bed but I thoroughly dislike the bed overall. After spending so much time and effort into leveling the bed, making sure that all four corners are the right height and stay there consistently, disheartened is the best way to describe how it feels when you try and level the center of the bed. No matter what I did, the center of the bed was always too far from the nozzle. To fix this, I raised the bed but that causes all of the corners to now be too close to the nozzle. After much searching online, I came to find that this is a common issue and that the bed could be "cupped". A simple fix is to buy a 235mm x 235mm glass bed but that can be like throwing money at the problem. - PTFE tube and couplers - This issue may not present itself in the beginning but over time, you may notice consist under-extrusion (like having holes or gaps in the print lines) no matter what your settings are. A quick synopses of the issue is the coupler that holds the PTFE tube in the hotend slowly lets the tube back out as filament is fed in. This causes the filament to melt and expand to create a jam. No matter what your settings are in general, you're going to end up with poor print quality. There are videos online on how to get around this but again, you're spending money to fix the problem. Overall, I recommend this printer. While my experience may be vastly different from someone else, I seem to be having a similar experience to many other people online. I love the price point of the printer and that it helps you understand the 3D printing world. My advice is to do your homework. If this printer is exactly what you want and you don't mind that you may have to learn some things to get this running smoothly, then I hope my review has given you some insight.

I am very happy with my Ender 3 V3 SE. It is my first 3D printer, having some experience with them in the past. This printer performed to an excellent standard and required very little setup out of the box. Unfortunately, the SE does not talk to the Creality Print software, and does not have WiFi or Ethernet network connectivity. Basic functionality is through physically moving an SD-card from your computer to the SD slot on the printer. It has a USB-C outlet that can be connected with a data cable to a computer and communicated serially with COM ports and the CH340 communications driver, it’s not complicated, but it’s not a straightforward process. After about 50 prints or so, the bearings on the Y axis optical rails came loose and resulted in a bed wobble that could register on the Richter scale. I upgraded the Y axis and X axis to linear guide rails, I do believe these upgrades are wholly necessary if you wish to print at the printers upper accelerations for any extended period of use. Changing filaments is a breeze with the direct drive extruder, I have printed in PLA, TPU, and PETG all with very good quality, adjusting settings along the way. If you enjoy tinkering, and learning how FDM printers work, how slicers and gcode work, and want a less expensive start to the hobby I would highly recommend the SE printer. I have also heard good things about its sister the KE.

The first few weeks with this printer were actually pretty rocky. I was having lots of printing failures and quirky problems. Many were due to user error and lack of experience, a few were made worse by poor usability design. Whoever designed this printer didn't really think through some things. This takes tweaking out of the box. With that said, I highly recommend this printer to someone who is looking for an amazing printer at a lower price, is good at troubleshooting prints, and is capable of problem solving and addressing some out of the box product issues. The cons list, while long, is all easily fixable. For the price you pay, these types of adjustments are completely worth it. Cons: -You must assemble yourself. This majorly increases the risk of breaking something or installing something wrong resulting in crazy printing problems. This also raises the risk of voiding your warranty. So, be really good at building things and able to fix your way out of mistakes - The out of the box filament holder/location is just flat out ridiculous. You'll need to print several additional parts if you want filament that doesn't interfere with your z-axis lead rod. -The frame is very prone to vibrations that affect the print. You'll need to print out feet to absorb the vibrations -The fan on the computer unit is in about the worst place imaginable. you'll need to print out a shield that redirects the airflow to avoid filament falling into the unit and the front left corner of the bed cooling off. -The wires were seemingly designed to get hung on the frame. you'll need to print several parts to slope the edges of the frame and do some cable management to avoid them getting hung on other parts. - The LCD screen has no backplate so you have a bare circuitboard exposed to whatever decides to bump into it. You'll need to print a backplate if you want to keep it protected. -The bed is so dad-gum hard to get level and keep that way. One tiny little nudge can throw the whole thing off. The springs are very weak and don't really hold in place for the first few weeks of use. You'll probably want to buy replacement springs or be VERY CAREFUL when interacting with the bed or anything remotely near the bed. -The x-axis belt is slightly too big, meaning that you're going to get ovals instead of circles out of the box. I used one of the included zip-ties to tighten the belt where it fits into the printhead notch and now it works fine. -the z-axis lead rod is crooked. IDK how to explain this or why it is this way, or how I fixed it but it is legit out of the box crooked. I think I blacked out while fixing it because I can't figure out how I straightened it out. Mine still has a slight slope when the arm is towards the bottom of the bed. IDK. Maybe I'll never understand. There are some parts you can print that are spacers for the unit, but keep in mind the frame acts as a heat sink so you'll need to add some raspberry pi heat sinks to the z motor to keep it from overheating. -this thing grounds by plugging in to the wall. That is fine and normal, but KEEP THIS IN MIND and make sure whatever you plug it into has a verified working ground. My surge protector was broken and the ground wasn't working. So I kept having massive crashes with the machine. Turns out static was building up during long prints and shorting out the machine. Yikes. Again though, this isn't the machine's fault. Just adding this in because it's pretty important to understand. -Cura doesn't have this printer listed in presets. You have to take the cura 10 settings and tweak them. There are lots of tutorials on youtube on how to get the best out of this printer so prepare to watch a lot of videos and have a lot of filament sacrificed to the test print gods. Pros: -price is like...wow. Amazing -the bed size is huge and really gives you room to create some awesome stuff -you can get some incredible quality prints off this puppy. Once I got mine in a good state I was astonished with the quality -can print at pretty high speeds and retain quality -it has print recovery that works surprisingly well in the case of a power interruption. -Is at it's core a very good little printer that is highly capable and reliable ONCE YOU ADDRESS THE ABOVE CONCERNS. If you're a beginner and you're looking for something easy to get started with, skip this and go with something like the monoprice mini v2. If you've been working with a beginner printer for a while and are starting to feel limited, and you're good at troubleshooting - I highly recommend this printer. It's worth it.

The Ender 3 marked my entry into the 3D-printing world, and I love it! The 3D printer has been a godsend! If you're also newbie and searching for advice, here's my brief take on the Ender 3. It's awesome! The Ender 3 arrives in pieces that you must assemble. Since it is essentially a robot, assembly can seem overwhelming at first, but if you take it one step at a time, you'll be printing in no time. I found the printed instructions accompanying the unit to be more sizzle than steak, but, fortunately there are several videos on YouTube that make assembly a breeze. Believe it or not, assembling the unit yourself is beneficial because it familiarizes you with the device. It will allow you to easily make the minor adjustments that 3D printers often require. My wife and I have found that 3D printing comes with somewhat of a steep learning curve, but it's fun. YouTube and websites such as "all3DP dot com" have proven themselves to be life savers. The most common adjustments you'll make while 3D printing is "bed leveling." In truth, though, you're not actually "leveling" the print bed, but rather you're ensuring that the print nozzle is uniformly distanced from the bed (the print surface) on all its 4 corners. The nozzle needs to be super close, too. ...not about an inch or two away from the print bed, but rather it needs to be no further than the thickness of a piece of paper. Crazy, huh? When my wife and I printed a test file provided by Creality (the manufacturer), we frankly sat mesmerized at the unit's precision. It was like staring into a campfire and getting lost in the flames. The nozzle just zipped back and forth across the print bed leaving tiny bits of corn-based "plastic" one layer at a time, and eventually (over time) created a cat/dog thingy. In search of more things to print, we settled on two websites with tons of 3D-printable files that are very often free to download. The websites are "thingiverse dot com" and "cults3d dot com". The latter site takes longer to load, but seems to have more options. Creality has one too, but I haven't really checked it out yet. It's important to note that the files you download from such websites are *.stl files, whereas the Ender 3 needs *.gcode files. To make the file conversion, we downloaded a piece of software called Cura. It appears to be the best (free) software on the market for "slicing" 3D files into *.gcode files. That too has a steep learning curve, complete with complicated settings. But fortunately there are lots of tutorials online along with settings you can copy from experts. I mostly rely on "all3DP dot com" for that. After a while, we decided to invent our own designs and then print them into existence. In my opinion, the cat's meow -- the best and easiest 3D design application -- is Fusion360. It has a limited free version for students and schools, but otherwise it's quite pricey. My wife then found free, open-sourced design software called FreeCAD. We love it, and haven't turned back since. The filament we prefer is PLA. In our experience, PLA produces little to no fumes and it's guilt-free because it's corn-based and biodegradable. It should be noted, though, that not all PLA is created equally. This is primarily because (according to what I've read) pigments affect the PLA in different ways. So, when I order PLA from Amazon, I always look for the PLA with the most and highest reviews. Then, I refer upon their temperature recommendations. Overall, we absolutely love the Ender 3. At under $200, it's extremely affordable, and the process of printing things into existence can be (in my experience) somehow transformative. And if you find yourself confused about something, take my advice by not wasting time by trying to figure it out for yourself. Just refer to the experts on any of the websites I mentioned so, later on, you can focus on things that really matter...like design. Note: the bearing on a little fan went out. So, I reached out to Comgrow, they got back to me immediately, and now a new fan is on the way. No fuss no muss. Finally, at the risk of getting to personal, I'm a disabled veteran who benefits from focusing on tangible things. The process of 3D printing has proven itself to be such a godsend in that regard, that I think the VA should seriously explore ways of getting more vets 3D printing. I hope this helped newbies like me. Happy printing!

so I bought this printer almost a year ago and I didn't even use it that much, I dont know exactly how many things I printed but definitely not even more than 20 this thing has less than 100 hours of printing and the amount of issues ive had is just stupid. I remember I printed less than 5 things and I had come across my first issue.. my prints kept coming off the print bed, it took me a bit but I realized I could just put some glue on it (like school glue sticks) and they would turn out fine (although I did have to clean the bed after every print) then I found this really awesome dragon, so obviously I printed it... well tried to print it. first time I tried to print it the nozzle clogged and I was kind of annoyed because it was like a 2 day print and it had printed for about 15 hours before failing and wasted a good chunk of filament, but I thought it was just you know a little mishap I mean not everything was gonna print perfect so i just tried again.. same problem so I changed some settings made sure everything was fine and I tried one last time. anddd surprise surprise it clogged AGAIN at this point I was starting to get pretty frustrated and almost just gave up but first I tried one last thing, changing the filament and same damn problem. then I didn't touch it for a while like maybe 4 months before getting the urge to start printing again, I watched every YouTube video, read every article online, and searched Google for hours to find all the possible problems and their solutions, I messed with every setting on the slicer, replaced the nozzle and I tried that dragon once again. this time I got about 70% into the print and I was super excited because it was almost done so I woke the next morning ran to the garage just to find out it failed with the same friggin problem as before. I thought maybe I just had to stick with printing some smaller quicker prints because obviously this dragon was just not working so I did that, and then another problem popped up, the thing wouldn't turn on, I'm not gonna explain the whole process but basically I had to reset the sd card and to get to this point i had spent about 4 hours trying to figure out what had happened and how to fix it when i simply got lucky took out the sd card and it suddenly worked anywau after that i tried printing other smaller prints that had previously printed just fine just to find out that all the other prints I tried were also failing. I bought some more nozzles in a variety of sizes and types of nozzles but before it even arrived I found out a piece of filament had gotten stuck in the Bowden tube again this had happened before and I had to cut off a part of the tube but now it was stuck right in the middle so I had to get a new tube but I was so frustrated with that thing that I just gave up this thing has been nothing but problems and I'm done trying to fix it only for another problem to reveal itself, I didn't talk about all the issues because I'm already tired of typing and you get the idea. I haven't even spent that much money on this to fix the issues because I've read lots of reviews of people spending double the price of the printer itself to try and solve these problems but ended up still broken. TLDR: dont buy this thing sure it's cheap it's one of the most popular beginner printers and really one of the most popular of all time but honestly it's trash, all the problems are just not worth it, I've spent way too much time trying to fix this thing. if you want a decent printer that won't cost you an insane amount of money you can get something like an elegoo Neptune 3 or a anycubic kobra for around 200-300 dollars sure it's more expensive but it will actually work.

**** Update 3/27 - So after a few days of printing, one of my belts started slipping. That caused my larger prints to slip off to side at certain points during the print. And it's getting progressively worse. I've contacted the manufacturer to see what they can do to get me replacement parts, but as of now, my printer is no longer functional. When it was working correctly, it worked well. But now it's just a very large $200 paperweight. See below for my review before the issues. So there is definitely a bit of a learning curve, but with the Creality Ender 3 and the included Creality Slicer program, learning is both fun and easy. I'm on my 3rd day straight of printing various things. I started Thursday with some small ship models, the Friday I tried some different small models, putting several models onto the same print job. I also did 2 tank models for my second print job Friday night. Today I printed an X Wing Tie Fighter combo and am now working on Klingon battle cruiser measuring 105 mm by 144 mm by 27 mm, my biggest print job yet. And most of my results have been very good. I've had some misses too, but thats mostly in the print settings or because I've scaled on objects print size too small. When you use the slicer program, make sure you choose to set the advance printer options. There you can choose nozzle temp, bed temp, print speed, and fill density, and other parameters that can make or break your model builds. To get started printing, go to some place like Thingverse and choose a model you like. I recommend trying smaller models first, with varying degrees of model complexity and detail. Then play with the settings in Slicer to generate the best gcode file for the model you are trying to print. The assembly of the Ender 3 was fairly straightforward and easy but at a relaxed pace will take about an hour to complete. Be careful during assembly that you don't get the cables tangled in the structure as you will need to have slack when plugging the various cables in. You are provided all the hardware you need plus the tools to complete the assembly. You are also provide a scraper for removing models from the print surface, and wire cutters if you choose to use the zip ties to anchor your cables to each other or the frame. Use the enclosed USB to TF card device to install the Creality Slicer software and the manual for the software. You will also use this to load your gcode print files onto. It's easiest to put your models onto the TF card then print off that directly from the printer. I've had this sitting in my cart for quite some time now, and now that I have it I am sorry I waited so long to buy it and get started. It's an amazing deal for a printer that works so well.

I have been thinking about buying a 3d printer for a little over a year. They have been pricy so I've not stepped into this arena, especially with so much information to wade through. So I bought this printer on a whim with a "lighting deal." First, I read other reviews and found YouTube for assembling the printer. The instructions help a little with the videos, but this is really the only negative. It's well made and simple to assemble so it made for a fun afternoon. Next thing to know is that I didn't know nearly enough. Once it's assembled, you have to level it. Luckily there's a ton of videos on this, and the assembly videos will go through that as well. It's not hard, but something I never thought of. I also got the auto leveler and installed it a few days later. That's a whole different thing that is amazing once you figure it out. Another thing i didn't realize is the print bed. This printer comes with one, obviously, and it does a good job. Keeping the bed level is hugely important for your prints. Also keeping it clean. It's never really clean though. I watched a ton of videos about using alcohol to clean it but that can actually be too harsh. Soap and water seems to be the go to across forums. Using some other adhesive is fair game as well. I didn't realize how much damage I did and bought a glass bed for my prints. Glass was amazing! It actually struggled to get prints to release. But the alcohol was too much and had already started to ruin my new bed. So, just soap and water should get you through most issues (and don't be afraid of the glass bed, it is pretty nice) Now, your filament absorbs water. I also didn't realize this and thought the various filament storage and dryer were just frivolous. They are, and they aren't. I have silica beads, and a vacuum sealer, so I don't strictly speaking need one of those. Also, my oven has a dehydration setting. However, it's nice to just have one on hand and not take up the kitchen or extra electricity from having the oven on. So, need one, no, but I'm not mad that my bundle came with one. Most of the rest of your questions can be Googled. But also, read forums, not just the popular videos and articles (it's how I've ruined two print bed). Everyone loves discussing the slicer (print configuration software basically) settings ands getting the most out of each print. I'm personally looking forward to learning to build my own designs, but don't feel like you have to. My kids love me printing endless frogs and cats for them to display and show off. My nephew likes the toys I've managed so far. Above I've mentioned things I've learned and wish I knew more about ahead of time. However I haven't really talked about the printer itself. It's been great. There's no real instructions because each print is a little different. You need to experiment to see what works best with everything. That may not be for everyone. But you can create surprisingly large prints with great detail with this printer. It's been smooth! It's worth noting that 3d printers can be loud, but it's not very. If say it's more quiet then most dot matrix printers. I can sit by it printing and work on other projects, or leave the room and I can't really hear it. So if you're wanting to break into this as a hobby, this is an excellent printer to start with. It's a little older so there's tons of help out there for it and it's been reliable. Replacement parts are not expensive, nor are upgrades. TLDR: This is a good printer and I'm happy with my purchase.

I've only printed a few things so far but it's enough to give some good feedback. At this price point don't expect any frills. That said this bare bones printer performs great. First off from my pictures you'll notice I upgraded the print bed to glass. It's only an extra $12 at the time I purchased. I read some other info online that lead me to believe this would be more likely to be level and perform better. i don't regret it. It works great. My advice would be to take your time assembling this printer. Expect it to take about 4 hours, perhaps more. Make sure everything is tight and aligned properly in terms of the rollers, belts etc. Do not rely on the quick start guide or included instructions. Go out to Youtube and follow the assembly video. Pause it for each step. When you are done stay on Youtube. There is a "Complete beginner's guide" on there from an Australian creator that demonstrates using this exact model. I noticed his menus are a little different due to software changes but his leveling guide and calibration files work great. For being one of the cheapest printers you can get the performance is surprising. I'm very happy with the print quality. I love that I can use tools on Linux or Windows. You don't need to be plugged in as you can simply print from G code on the included micro SD card. The videos online can get you up and running quickly. Every tool needed to build and run the printer are in the box. Nice touch. There is a small amount of PLA material but you will want to order more right away. The included spool is small and really only enough for a couple test prints. If you are a beginner why spend more? This is the perfect first printer. Update: I thought I would add to my review now that I have had some time working with this printer. I've made a lot of improvements to the device I first received. The nice thing is most of the improvements are cheap or you can print them. First thing to note: I was having a lot of problems with printing anything large that took a bit of time. After a lot of digging I found the hotend shipped with the printer was (in my opinion) put together wrong. They either built it cold or inserted the nozzle before the heat break. Either way there was a gap that could not be fixed in the hotend. I bought a Creality spider hotend which is all metal. Way better and it works great. Add to that a BL Touch sensor for autoleveling the bed. Best addition ever. You still need to start with a level bed but it fixes all the little problems with uneven bed surfaces and stopped my extruder problems. While on the extruder. Calibrate your machine! Take the time to measure the output from your extruder. They use a generic setting from the factory. You NEED to set up this machine. Calibrate the extruder, the retraction distance, the nozzle temp for the filiment etc. Pay attention to the details and you will get great results. Really happy with this printer. It takes work but it's a fun project that leads to other projects, and for a beginner it's hard to beat. Some say you should buy higher end and avoid all the minor issues. I disagree. I think this has been a learning experience that prompted me to understand the machine. I think that basic knowledge of the process is important. Your mileage may vary.

Ich bin ein 3D Druck Neuling. Daher war der Ender 3 pro auch mein erster 3D Drucker. Vorerst war ich etwas geschockt über einige schlechte Bewertungen (sowohl auf Amazon, als auch auf YouTube), die über verzerrte Drucker und durchhängende Druckbetten berichten. Jedoch habe ich mich wegen des guten Preises für den Ender 3 pro entscheiden und wurde nicht enttäuscht. Der Aufbau des 3D Druckers war sehr einfach und toll in der Anleitung beschrieben. Auch die Verkabelung war sehr eindeutig in der Anleitung beschrieben. Im Vorfeld habe ich mir schon eine 3D Datei vorbereitet und diese im Prusa Slicer gesliced. Nach dem Zusammenbau habe ich den Drucker an den Strom angeschlossen und die SD Karte mit der G Code Datei eingesteckt. Nun habe ich die Nozzle vorgeheizt um das Filament einzufädeln. Das ging nicht so leicht wie erwartet, ist aber mit ein bisschen Fummelei schnell zu machen. Anschließend habe ich den Druckvorgang gestartet und der Drucker fing mit dem automatischen Nullen der Achsen an und heizte danach das Bett und die Nozzle. WÄHREND DES GESAMTEN DRUCKVORGANG STAND ICH IMMER MIT EINER HAND AM STECKER DES DRUCKERS, UM IHN ZU STOPPEN, WENN ETWAS PASSIERT, DAS SICH NICHT RICHTIG ANHÖRT ODER NICHT RICHTIG AUSSIEHT. Fazit: Ich bin sehr alles in allem sehr zufrieden und habe einen guten Start in den 3D Druck bekommen. Die Druckqualität reicht mir, ist aber wenn es um Feinheiten geht manchmal nicht ausreichend. Für große Drucke reicht es aber alle Mal! Er bekommt von mir klare 5 Sterne, weil er ein super Einsteiger Drucker ist, der mir einen tollen Start in den 3D Druck gewährt hat. Große Empfehlung!

Die Rezension bezieht sich auf die Version Ender 3 Pro V1. Inzwischen gibt es die V2 die klar bevorzugt werden sollte da diese das Silent Mainboard vorinstalliert hat. Als Einsteiger in die 3D Druckwelt habe ich mir dieses Modell gekauft da es recht verbreitet zu sein scheint und dementsprechend einfach Hilfe bei Problemen zu finden sein sollte. Aufgrund diverser Empfehlungen aus dem Netz hab ich den Drucker von Anfang an nicht in der Standardkonfiguration betrieben sondern ein paar Teile ausgetauscht: - Capricorn PTFE Schlauch - Redrex Bowden Extruder Aus dem großen Thingiverse Schatz hab ich mir auch das ein oder andere Upgrade selbst gedruckt. Für die Druckqualität wichtig scheinen so kleine clips zu ssein die ein wackeln des PTFE Schlauchs verhindern. Der Aufbau ist mehr als simpel und sollte niemanden vor eine Herausforderung stellen. Einzige besonderheit die ich auch im Netz nachgoogeln musste: Der Schlitten der x-Achse also wo der Extruder dran ist war nach dem Zusammenbau seeeeeehr wackelig. In der Anleitung nicht erwähnt wird, dass an der unteren Schraube mit der Rolle eine Exzentermutter angebracht ist die gedreht werden kann damit der Schlitten spielfrei läuft. Jetz der wichtigste Punkt überhaupt: Lasst euch zeit beim Einstellen des Bed Levelings. Für einen erfolgreichen druck ist es das A und O. Beim ersten Versuch hab ich nicht richtig aufgepasst und es zu eng eingestellt, sodass die Düse leicht "durch" die Magnetplatte gefahren ist. Zum Glück nur am Rand, aber es wäre ärgerlich es auf die Art kaputt zu machen. Ebenfalls ausdrücklich davon abraten möchte an diese Platte mit dem Spachtel zu gehen, da man jedesmal einen dünnen teil der Oberfläche mit abträgt. Wenn das Bed Leveling stimmt lassen sich Reste oder ähnliches leicht mit dem Fingernagel entfernen. Auf der beiliegenden SD Karte sind 2 oder 3 Beispiele drauf. Es ist Zeitverschwendung diese zu Drucken. Ich habe in meiner Unkenntnis das Sparschweinchen gedruckt. Es dauert nicht nur ewig, die Qualität ist auch absolut mies. Daher lieber etwas schönes aus dem Netz suchen und durch den Cura Slicer schicken, die Qualität dieser Drucker ist einfach nur unfassbar besser. Keine Ahnung warum der Hersteller hier sein Produkt unnötig schlecht macht. Die Lautstärke in der Roh-Version (die es inzwischen wahrscheinlich nicht mehr gibt da durch die V2 abgelöst) ist... nicht Wohnzimmer geeignet. Definitiv nicht! Durch Austausch des Mainboard und diverser Lüfter lässt sich durchaus was rausholen. Da es mein einziger Drucker ist konnte ich die Qualität nur anhand einiger Youtube Videos mit anderen Modellen vergleichen, aber ich selbst bin überaus zufrieden mit dem was der Drucker ausspuckt. Die Bedienung ist sehr leicht und wie erwähnt empfehle ich den Cura Slicer dessen Ender 3 Profil "perfekt" ist. Hatte jedenfalls keinen Aufwand daran herumzufummeln oder Werte anzupassen, das lieferte Out of the Box prima Ergebnisse. Ich habe bislang ausschließlich PLA gedruckt, kann also über andere Materialien nichts sagen. Nachträglich habe ich mir das Creality Board 1.1.5 Silent zugelegt was die Lautstärke der Stepper massiv reduziert. Inzwischen würde ich allerdings zu dem neuen BigTreeTech 2.0 Board raten, da dieses nicht nur Silent Stepper Driver verbaut hat sondern auch einen größeren 32Bit Controller verwendet, der genügend Platz für alle Features der Firmware bietet während die Crealitiy Boards nur die Sanguino atmega1284p verwenden die einfach nicht mehr den benötigten Platz bieten um "alle" Features der Marlin Software unter zu bringen. Ebenfalls habe ich mir Dämpfer für die Motoren gekauft, diese sind aber nur mit SEHR VIEL gebastel am Gerät anzubringen, da die grundlegende Konstruktion nicht für ein vergrößern der Abstände ausgelegt ist. So müssen beispielsweise die aufgepressten Riemenzahnräder weggeflext werden und durch Schraubbare ersetzt werden um Abstände auszugleichen. Diese Modifikation würde ich nicht nochmal machen. Fazit: Würde ich das Gerät wieder kaufen? Ja definitiv. Es sind zwar meiner Meinung nach einige Mods und damit Zusatzkosten nötig, aber da ich gerne Bastel ist das durchaus Willkommen. Die Druckqualität ist meiner Meinung nach hervorragend und die Bedienung kinderleicht, kompliziertester Teil ist das Bed Leveling.

****UPDATED FEBRUARY 2021**** Most problems have been solved, thanks! They sent me replacement and/or partial refunds for the problematic parts. Thanks a lot! Ender 3 pro is long to build - be sure to watch Youtube Videos as written info isn't enough - but it's fully customizable, affordable and printing quality is amazing. You have to put some efforts into it, beware, but the satisfaction of your 3d printer working perfectly is worth it.

Comprata come regalo per mio figlio, alla fine è stato un regalo anche per me. È una stampante entry level, ma stampa veramente bene con una qualitá che mi ha sbalordito. Non posso fare altro che consigliarla. Ho comprato poi anche sensore per filamento, indispensabile se non vuoi buttare via la stampa se a metá termini il filamento.

Product is simple and amazing. I am looking at functionality versus absolute quality and this is perfect for me. The product has been handy for making anything u can think of. I was able to quickly draw a repair part for a washing machine and that has recoverd a third of my investment here. With some free 3d online files, i've managed to make my printer more compact. Only cons for any enthusiast is the purchase of 3d drawing software if Tinkercad aint enough.