TP-Link Deco BE33000 Quad-Band WiFi 7 Mesh System (Deco BE95) for Whole Home Coverage up to 7800 Sq.Ft with AI-Driven Smart Antennas, 10G Multi-Gig Ethernet ports, Replaces Router and Extender(2-pack)

Trabaja muy bien, super veloz. El único problema es el conector de alimentación a la corriente eléctrica se desconecta con mucha facilidad solo, no embona bien o es muy corto y no se alcanza a fijar bien al aparato.

I bought the Deco BE95 to replace an Orbi RBK853 (WIFI 6) system. Although I my internet was a 1.5Gbs service, the Orbi was only getting 500-600 Mbps downloads to my devices and we experienced unusual drops and a few areas with poor coverage despite 3 units all connected via Ethernet. It took me about 15 minutes to set up the Deco BE95 and configure it with the same network name and passcode so all of our devices immediately reconnected. It was an exceptional decision. With only two units (vs. 3 for the Orbi), I’m getting full 1.5 Gbps downloads on our WIFI 6E and 7 devices. On older WIFI devices, I’m getting 650+ Mbps downloads. On the WIFI 6E devices, I’m getting 900-1000 Mbps in areas of the home the Orbi (with 3 units) was struggling to get 100-200Mbps. It was super easy to set up and I’m getting full speed within 40 feet of the Deco and almost full speed everywhere in the house. And, when my internet provider soon switches to 3Gbps internet, I’m confident the Deco will handle that with ease also. Great purchase and future proofed WIFI.

So this system has the best coverage and speed I have seen from a mesh system. So I purchased a 2 pack of these to cover a 3600sqft 2 story house. Now on average we have minimum of 55-60 devices on our network daily. Our family streams a lot of content and with the kids gaming our needs are quite great. My internet is 5gig fiber with symmetrical speeds. I have one unit upstairs and 1 downstairs both located centrally on each floor. Now these units are big and there heavy so I also purchased the wall mounts for this specific model which made things much easier. Now getting this system up and running was an absolute breeze using the deco app. I plugged my first unit in now with these it doesn’t matter which one you use and both units are identical in these sets. I have this first one plugged directly into my ONT with cat 6A cable. I then proceeded with the setup and once I got the first one up a running I plugged the 2nd one in and waited for that one to sync. Since these sets are matched pairs there’s no special sync process needed. Now once they were both up and running the deco app installed a new firmware update which took under 5 minutes to complete. Once both units were back up all my devices connected immediately without any problems. All devices came back online and the stability was outstanding everything from our tv’s to our cameras has absolutely excellent signal to each of them and speeds across my wifi 6E and WiFi 7 devices was incredible. Now I tried my satellite node both with wireless backhaul and my normal wired backhaul because I was curious what the speeds would be. Now wirelessly my download was 1.3gbps and on the upload I was at 1.2gbps which is absolutely outstanding. I then went back and plugged my cat6a cable into my downstairs satellite to achieve my wired backhaul with my device topping at a staggering 1.9gbps on the download and 1.6gbps on the upload and again outstanding performance. While there’s a definite difference with wired backhaul this systems performance is very good in both scenarios. Since this is the flagship model the overall value of this while steep on price your definitely paying for a premium quad band system that has insane coverage and speed capabilities. Bottom line this system has massive potential and controlling the system is very easy and it even has a very basic webgui if your not a big fan of cloud based apps either way this system performs as it should and does everything very well.

Lasted about 15 months. The failure mode was pretty weird - uplink speed dropped to the point where it was almost non-existent (at first I thought it was my ISP, but that was quickly ruled out by connecting directly). Might be my largest waste of money to date, considering performance was always underwhelming. Now, I’m getting better performance than I ever got from the Deco mesh routers from a new, much less expensive set of mesh routers with theoretically lower specs. As a bonus, the new routers don’t throw off heat like the Deco did.

This unit, the BE95, is the flagship product for TP_Link home mesh networking. As a retired IT professional/engineer who worked with hardware and wrote more code than I want to remember, I have only high praise for the BE95 product. The incredible overall total throughput along with the capabilities to handle in excess of 200 connected devices fleshes this device out to be almost ultra-commercial in design. We had a very high end gaming router with some repeaters prior to this unit. We also have prior mesh systems from Asus as well as NETGEAR (Orbi) and they all sucked. Confusing back channel configurations and inconsistent connections plagued our connectivity daily. Originally I balked at the price, but figured I could just return it if it didn’t pan out and live up to promises. In the end, with just the 2-tower package, we are covering our entire home of 3000Sqft with full 5 bar connectivity and absolutely ZERO dead spots. Where we had constant drops and interruptions in our old system for our xfinity WiFi enabled tuner, we now see consistent 4k television. When I look for WiFi I look for reliability and signal quality. This unity excels at both. Even all the way back by our fence at edge of the property I get full bars. Walls are not a problem as the unit utilizes MLO (multi link …Ah crap, can’t remember what o stands for) in short, it will use more than one of the 4 channels to make sure there are no dead spots in the signal. The back channel is automatic and seamless. Once setup with the free app, you rarely need to access it. And speaking of the app, it is the only detriment to the system as the fine folks at tp_link decided to rely solely on the app for configuration of port forwarding and other granular stuff. There is no way to do that on the web based on fig tool I’m not sure if it was left out on purpose or if the unit was rushed and web app,just didn’t get finished in time. It does not feel like a rushed product so, some how I think they just left it out to avoid confusing the average person. The system provides connectivity on WiFi specs from 2.4g, 5g, bands as well as 2 others. High spectrum reserved for back channel connectivity to ensure quality service. WiFi 7 compliant (spec not completed yet but it will be soon) there is no WiFi they cannot connect to. The ports on the back provide 2 2.5 gig Ethernet and 2 10gig Ethernet/ as well as a high speed usb for attaching some hard drives for network attached storage. This thing is made to scream while pushing as many bits as possible. Over saturation of the network never happens. I can be transferring large video files, watching 4k tv, streaming something else, listening to music and have a torrent client running in the background while my son kicks butt on his gaming servers with ultra low lag….on WiFi. Faster than the Ethernet connect on our old router/ap. I can confidently say, barring some magic leap in tech, this will be he last WiFi router we buy for at least a decade. Highly. Highly recommended. This from a guy with 4-5 boxes of old devices sitting in his garage!!!