EZDIY-FAB Shield ARGB M.2 2280 SSD Heatsink, Built-in 20mm PWM Fan, White | Active NVMe Cooling, Dual-Sided Heat Pads, Aluminum Heat Sink, 5V 3-Pin ARGB Sync, M.2 2280 SSD Support, NVMe SSD Cooling

Seems pretty effective, within reason. I have drone footage that I move back and forth from my primary SSD and with this active heat sink on both drives, it takes a couple of minutes before the drives throttle down their throughput. Before, I'd get 10 seconds, tops. They're on the same bus, so it's the fastest data transfer I've ever witnessed on my machine. I don't know all the intricacies of read/write IO or buffering, I just noticed a considerable performance increase with cooling vs none. RGB is nice to put in sync with some of the other lighting my rig came with too. So, unless all you do is make bulk transfers between drives, these little active sinks work quite well, and I can see them keeping game loading times to a minimum.

I'm absolutely blown away with the performance of this little NVME cooler. The heat-sink on this thing is MASSIVE in comparison to an actual nvme size and the two thermal strips that go above and below the nvme must do a lot of work in terms of cooling. The heat-sink and cooler itself is surprisingly heavy and the RGB is beautiful. It comes with a tiny screwdriver and installing it is a breeze. Once you place the thermal strips on and unscrew the heatsink, you place the NVME in between the bottom slate and the heat-sink and close it. After that, the nvme becomes one with the heat-sink/cooler and you just install it like normal. The nvme is daisy chain compatible and the fan plugs into any fan slot on the motherboard. I cannot hear the fan at all no matter how close I get to it. When everything is done, the results speak for themselves. 16C drop... unreal. For the price and the performance, it seems like a no brainer. I'd imagine even without the fan, this would drop the temperature like crazy due to the massive heat-sink. The best part of all, it's aesthetically beautiful. It literally looks like a mini-GPU. One of the best computer accessories I've ever purchased.

4 pin fan control and a 3 pin RGB plug are needed to get the most out of this and the inch or so of clearance above the M.2. Just wanted to get that bit out of the way, compatibility was my worry. That said this thing inspires great confidence. From the secure fit of the screwed in M.2 bay in the heat sink to the snug fit it has inside the fan cool aluminum block and of course the looks, this thing is great. Easy to mount, sticks solid in place, keeps things cool (both looks and temp wise). My only advice is double check you have the physical clearance! This fits my smaller PC no problem but my full ATX board has zero room for it.

This cooler is amazing. Picked up a 4tb samsung 9100 pro for great deal so I stuck it in my pc. The temp on ssd was 105 degrees under load. Picked this cooler up. My ssd doesn't go over 55 degrees under full load . The rgb looks great but the performance is amazing.

Works a lot better than I expected, was afraid I would have to modify my z790 ROG Hero Maximus motherboard in some way but it ended up fitting just fine. Has great airflow and keeps my Samsung 990 Evo Plus and 970 Evo from getting hot like it use to, they use to get to 70C now when I play Star Citizen they get about 50C or less. Sold construction and good quality. I very much recommend this. I need to get a 3rd asap.

Its a nice heatsink, reduced temps on my gen 4 nvme drive but only by less than 10 c, considering I had only a slim heatsink before I was expecting more of a difference since this is so big and has a fan.

M.2 cooler works and looks great

I bought the arg model. Installed on a wd sn850x 2tb ssd. Reduced temp by 10 degrees C. Over the stock solid heat sink. Back into a good working temp. Ran 4 passes on crystal and was very stable. My system maybe louder than some but it's very quite even maxed out. I have it set at about 70 percent speed. Easy install. I might change out to a different thermal pad just to see if it cools more. I used the secondary cpu fan controller for power, controls speed in bios. Rgb on a vacant slot matches existing lights. Asus b850x mother board Ryzen 9 7900x cpu. I'm not not a extreme gamer but I will install border lands 4 to see how it performs. It is a tight fit but no conflict and sits right above a rtx 7501 gpu. Looks good in the case

I put two of these things on an MSI MEG ACE Z890 mobo, one on a Crucial T705 NVMe5 4TB M.2 drive and the other to replace the factory heatshield on a Samsung 990 Pro 4TB, both 12 months old. The Crucial dropped from 68 to 55 under light load and the Samsung from 66 to 49. Now the NVMe5 drives do run pretty hot but the MSI mobo stock heatsink is a pretty robust static affair, yet this simple, quiet active heatsink has given me a heap of headroom to really get the thing cranking. Previously, I did suffer intermittent bouts of glacial performance during thermal throttling. It is early days, but I am thinking this is a reliable fix for that issue, undoubtedly greatly extending the ssd's life in the interim! Re the Samsung drive, it gets a fair flogging and the factory heatsink is just not getting the job done, totally fixed now. An identical drive, except it is a year older with double the hours and now on archive duty, is still running OK, but even it is at 55 while the newer one is now at 49. These new active heatsinks are a pretty easy install. Tight, but they fit just fine as they are short enough for both the slot connector and rear attachments to work, and a couple of mm wider which makes them tight for adjacent components, but no physical pressure, for my setup anyway. Without messing about with led settings, they produce a breathing rainbow effect through the full colour spectrum, very pleasant! I ordered another one to put on that older 990 Pro, they are pretty easy to take the covers off with a special screwdriver and a guitar pic.

Por favor, revise bien las caracteristicas de su hardware antes de comprar este producto. En mi caso no fue compatible ya que, por un lado, chocaba con el ventilador del CPU que tengo (Noctua NH-U12S redux), aunque tuve que reacomodar los tornillos para que pudieran coexistir, por el otro lado no permite que el seguro de la grafica (RTX 4070 TI Super) cierre por completo lo cual me causo algunas alarmas en la tarjeta madre, ahi si no hubo mas que hacer. Es por acomo de la tarjeta madre y los dispositivos actuales (Tarjeta Madrea Aorus B365) Ademas, mi pc ya no tiene conexiones dispobles para mas ventiladores, por lo que calculo que se requiere un concentrador de ventiladores/RGB. Se ve de buena calidad, viene con un manual que no es de gran ayuda ya que he tenido que buscar en linea como se instala. Incluyen un sticker de la marca y la garantia.

Buen producto, cumple su función a la perfección, baja de 8 a 10 grados

Perfect