CO2 Laser Lens Dia:18mm FL:3" or 76.2mm Laser Mirror CVD ZnSe Focus Focal Lens for CO2 Laser Engraving Cutting Engraver/Cutter 40W-200W

I have some unique glasses that are curved and tapered and I didn't think the standard 2" focal length lense on my laser machine would handle the varying focus depth.I started with a ramp test on this new 3" FL from cnole tech and found the ideal FL was 70 mm from work surface to the bottom flat face of the lense with a great focus in 2mm either direction a total of 4mm variance.I'm impressed with the ability to remain a relatively fine point focus at this FL. The Lense appears to be of high quality and was delivered scratch free with a perfect polish.

Works as expected and has made multiple cuts and engraves with no issues. Still is working perfectly. I will buy another when one is needed. Used on a Thunder Nova 24.

The 20mm FL:2" is a perfect drop-in replacement for the default focus lens on the Boss LS-1420 laser. Boss wants $100 for their lens but I found that this one was much cheaper and had all the same specs. So far I've run my laser for about 10 hours engraving and cutting 1/4" solid cedar and 1/8" baltic ply and am getting sharp engraves at 385mm/s, and clean single pass cuts. Just make sure you wipe your lens down often during jobs and get a good air compressor. My original lens lasted three years before I replaced it with this due to my own negligence. I've picked up another spare just in case I forget to wipe the lens down again.Make sure to pay attention to the direction of the curve on the lens, and also make sure to wipe down all your mirrors while you're swapping out the lens. Wear gloves and only handle the sides of the lens.

The lens was just a bit thicker than the original ULS M-300 2.0 lens - but it still fit perfectly in the lens carrier and the extra thickness didn't extend beyond the milled portion of the carrier. Any thicker and this would have failed. Just did my first cut and engrave with it and the quality looks good. It seems to me that some 5 years ago I had purchased a similar product and it did not fit. Stocking up with a few extra of these, now that I know they fit, just to have around.

I bought a 2.0" focal length CVD IIVI ZnSe lens, 19mm diameter. This lens is thicker at the edge than OEM lenses from universal laser, but it just barely fits, and cuts well enough so far. I bought another one that is listed as plano-convex like the OEM lens, but it is out of spec and too thick to use. The plano convex lens from universal laser is about 2.3mm thick, and 1.75mm thick at the edge. One caveat, which may or may not apply to all replacement lenses, is that you will need to re-calibrate your height adjustments to match the new lens. This one works best for me when I change the calibration from the original lens and set at -0.100" and re calibrate. This makes the table a bit higher, and makes the laser focus tighter than if not calibrated. I made a bunch of test cuts, going first with the calibration that worked for the OEM lens, and moving the table up in 0.050" increments. the kerf got smaller, at .050, smaller still at .100, and then started to get wider at .150 as I raised the table above the ideal focal length.seems to cut on par with a used OEM lens, using the same settings, once z height is recalibrated. I have not compared to a new OEM lens right out of the box. Given the price of this lens vs. the OEM lens, I am ok with having to re-calibrate in order to save some money.I have a universal VLS-6.60 cutter that I am using this in using the OEM aluminum lens holder. I removed the broken lens by soaking in acetone for a few minutes to soften old glue. After carefully cleaning old glue from aluminum holder, I used loctite AA 352 adhesive (a UV setting acrylic adhesive), and cured the glue with a small blacklight for a few minutes. clean up of any stray glue with a q-tip dipped in acetone was simple and easy. Make sure the lens is in the holder the right way. The convex side goes facing the aluminum lens holder. glue only in the corners of the holder if you don't want a giant mess. this takes a little bit of skill, but it is entirely doable, and seems worth the effort so far.

I managed to drop my original OEM lens while cleaning it...don't do that as they are very brittle.OMTech focus lenses were out of stock so I took a chance and just ordered from Amazon. The new lens worked but it seemed like my laser settings needed to change. It needed different settings to properly engrave powder coated stainless steel tumblers from what I had historically used. Not better or worse, just different. I only ran a grid test with power/speed to find a better setting. I never did try a ramp test to see if it was bacause the focal length was slightly different. Overall very happy with this relatively cheap alternative to buying from OMTech.

buen material

I cut the bottom out of my k40 to accommodate rollers and larger items. Being able to get the work piece away from the head has been awesome.

Muy buena calidad precio ,la mejor elección recomendado

Das wechseln der Linse ergibt ein weit besser Ergebnis. Die Linse muß richtig eingebaut werden und nicht mit den Fingern berühren. Beim Kauf auf den richtige Durchmesser achten.

Taille : Dia.12mm FL:50.8mm/2" commandeTaille : Dia.18mm FL:50.8mm/2" reçu

Tutto OK, Amazon sempre una garanzia

Quality product. Far superior to lens supplied with K40. Certainly made a vast improvement on cutting and reducing burn.