Boron Nitride Paste (5 cc) by Slice Engineering | Improve Conductive Heat Transfer | Maintain Stable Temperatures | 3D Printing | Thermowells | RTD Sensors | Thermistors | Thermocouples | Heaters

It is easy to apply and it goes a long way, I use it to install any nozzle on my machines. It also easily cleans up with water and is inert so getting it on your hands is perfectly safe. It really does improve heat transfer just like thermal paste on a cpu is needed for the heatsink to work, but heatsink thermal grease cannot handle the higher Temps in a 3d printer nozzle. I have noticed a bump in extrusion rate on every machine I have used this on.

*** Slice Engineering states (on their website) that the paste needs to dry out. You can either, let it sit overnight or run the hotend at 90c for 10 minutes. This is because the paste contains water: to aid in squeezing it out of the syringe and spreading it effectively.If you don't let the water evaporate/dry from the paste, you can experience the ~bubbling that others complain about: this is the water boiling away at high temps and pushing the paste out of place. *****Be cautious: the paste can push out of the tube with excess (upon first use, after it has sat for a long period). I would suggest trying to pull the syringe back a bit: before pushing forward. **Overall the performance of this Boron Nitride paste is exceptional compared to other general use thermal pastes, for 3D printing.I've got a P1S, running a V2 Aftermarket hotend w/ .4 CHT Bondtech Nozzle: getting ~30mm^3/sec.This paste really helps when you need to dissipate heat between the "cold-end"/Thermal tube: of the hot-end assembly, and the heat-sink; I also put a small amount on the threads of the nozzle. { Use caution to try to not let much of the paste get into the filament path. I didn't run into issues, even having done so. You can always use water to clean off excess paste: Iso worked well for me too. }I did run into temporary issues: getting thermal malfunction errors, because I didn't realize the paste needs to dry. ( It's also likely I didn't apply enough paste into the thermister hole nor push the bulb into the hole far enough: to get good/consistent readings.)Once you are aware of these several, obscure aspects of how to use the paste: properly, things work out great.Well worth the money, for what you get. I would recommend it for anyone seeking to improve their 3D printing experience.

Works as specified. Many of the heater cartridges are a loose fit and if they do not contact metal to metal well. There will be inconsistent heating of the block with just a set screw and potential thermal runaway issues. This compound has a high heat transfer. No more struggle to 300c+. Smooth consistent heating and stable temp holds. It's water-based instead of grease, so it cleans easy. Slice Engineering kept the price reasonable for a home hobby 3d printing compared to computer focused compounds. Product is a grand slam home run.

I ordered this for an all metal upgrade on a cheap bed slinger, but going to use this on every printer I've got going forward!Inititially, I bought this due to stringing after replacing the heatbreak with PTFE tubing down to the nozzle.I was a bit skeptical, but after filling the heater block (heater cartridge, thermistor, nozzle), as well as the heatsink chamber on the cold side my printer heats up faster and maintains temperature much better! The stringing is gone now, although I did have to make some adjustments - no fault of this paste though. This stuff truly works miracles.My only complaint is the tube it comes in, I tried to push as lightly as possible, but each time it builds up pressure until it shoots all over. Be careful if you haven't used it before, I used up 1cc on a single printer, but there was enough waste for probably 5 more!If you own a 3D printer, you need this!

This is great thermal paste for the creality k1c hotend. Holds up well after months of use. No drift and no issues calibrating pid. Lasts a long time too. I've swapped hotends multiple times and I have plenty left.

No way of knowing if this paste made a difference. I bought the heat break with the paste and applied it on the original install. However, I'm getting incredible results!If you bought a heat break and didn't see a big improvement I'd definitely suggest trying this paste.I did the 90c quick drying process described on the web site. No issues.The only negative is this stuff is messy. I was being careful, but it got everywhere. It's not difficult to clean up, but it's impossible to apply it without getting all over.

the paste is far more effective for hotends than other types of thermal paste. place a finger on the end when plunging the paste as it has a tendency to explode out forcefully. the applicator could thus use some tweaking but the paste itself is elite.

overall works great! and easy to apply! enough leftover to use for 2 or 3 more applications. easy to clean up too since its water soluble