ProxxonMICRO Compound Table KT 70, 27100, Green

Nice mini compound table works great for training kids.

This is a great value for the money. Its a great light duty precision compound table that adds quality to any project.

This is the best small X-Y table I've used and I highly recommend it for any small work. The gibs are very tight and precise and both axes move very smoothly with the traverse knobs. The ways are protected from chips, the gibs are adjustable, and the scales on both knobs plus a linear scale on the X-table are adjustable for ease of use. I work with watches and small clocks so this table is ideal for my use, and it's currently mounted to a precision micro-drill-press (Cameron 164). I can position any work item very precisely and it will be held securely for drilling. The graduated dials make positioning very easy and accurate. I am currently using this table with the Proxxon 24260 precision vise (excellent) and the Proxxon 24256 step clamps, both of which work well with this table. I'm an engineer and machinist and I have had several inexpensive import X-Y tables before that were practically unusable due to sloppiness, crude construction or poor fit of components, this table is completely superior to all of them and totally out of their league. Note that I am not associated or affiliated with Proxxon in any way, I just appreciate a well-made tool and I'm very pleased that Proxxon is able to offer these at such reasonable prices.An important cautionary statement: This is a SMALL X-Y table, it will not work well for large items and you cannot put a massive milling machine vise on it (like, for example, a Kurt D30 3" vise) it's just too small. If the Proxxon vise mentioned above is too small for you, I would recommend a 2" screwless toolmaker's vise, but nothing larger. Also, this table should be excellent for milling "easier" materials like brass, aluminum, plastic or jeweler's wax, and possibly mild steel if you are careful. But I wouldn't recommend it for tool steel, stainless or anything harder, it's not that the table is inadequate in it's own right, it's just too small and lightweight and you'll get too much vibration to get a smooth cut.

I have a relatively inexpensive drill press that I purchased from a Menards store in Carmel, Indiana, about 15 years ago but I was needing a milling table to attach to the press for milling out an 80% lower AR made of cast aluminum. I pursued some reading concerning the mill work that was required to turn an 80% lower into 100% and it looked like I needed a table that was adjustable down to fractions of a millimeter. When I received the Micro Compound table I realized that the AR lower barely fit on the table; however, I figured out that I could lock down one end by passing through the magazine slot and tightening the AR lower to the table with the use of a 1/4" drive ratchet (10mm socket) and extension and locking down the other end as in the instructions that came with the compound table: problem solved. I actually locked the custom milling jig (for the AR lower) to the table using the pass through bolts in the jig as attachment points. I made my own separate jig to bolt the Proxxon 27100 to the drill press table and locked the drill press table at 0 degrees. The Z axis on a drill press is adjusted by cranking the press table up or down but make sure the table is locked in position well after cranking or the press table will twist when the bit is engaged and beginning to mill aluminum - my left thumb nail learned a hard lesson. Note that drill presses are made to function vertically, not horizontally, so I did most of the cuts moving the end cutting milling bit vertically (treating it sort of like a drill bit) then finished up the edges by taking very small increments at a time (~0.1 mm) moving the bit laterally through the metal with the rotating edge always moving toward the metal for a smooth finish. I only had to tighten the set screws once to reduce play in the table. I won't admit how much time I put into milling out the 80% lower over the last month. However, now I have a fully functional AR lower which I began to assemble successfully yesterday. The Proxxon 27100 table worked well for this project. It will function even better for me next time now that I understand how to use it properly.

El producto llegó en perfecto estado y un día antes de lo programado. Excelente producto de gran precisión y calidad. Lo recomiendo al 100%

Excellent matériel de précision. Indispensable pour bien ajuster mes perçages de petites pièces pour la construction de mes maquettes de bateaux. J'ai ajouté un étau qui est livré d'origine avec la perceuse sur colonne de PROXXON. L'ensemble est bien fixé et parfaitement adapté. Les vis étaient dans l'emballage pour une fixation ultra solide. Livraison ultra rapide et prix parfait. Le vendeur est très serviable et compétent. Merciiiii

Produit de très bonne qualité.Rien à redire pour du Micromot.

Es ist ein sehr sauber verarbeiteter Koordinatentisch. Nach ein bisschen ölen ließ es sich sehr einfach und gut verstellen. Einziges Manko ist ein bisschen das Zubehör, ich hätte gerne ein zweites Paar von Schienen mit den 4mm Gewinden, ich denke dass ich das nachbestellen werde, aber ansonsten sehr gutes Produkt.

Helt nöjd