ELEGOO ABS-Like 3D Printer Resin, Clear Blue 2KG, High Toughness & Tensile Strength & Bend Flexibility Ideal for Industrial Components for LCD/MSLA 3D Printing

Prints come out sharp and tough with nice detail. Good balance of strength and flexibility.

Absolutely love this stuff, same results every time, no matter what. Perfectly captures sharp details, it's easy to clean up and a breeze to post process. It's also super easy to sand and it takes paint really well. This is my go to resin.

The best resin I've ever used for my printer. Great for printing D&D miniatures as it's not as brittle as other resins, meaning thin parts are less likely to snap during support removal. Very consistent and a nice colour too, though most things I've used it for get painted anyway.

I have finally made it to the bottom of this bottle so I feel I am no able to share my thoughts. The resin is very consistent between prints, and when cured is indeed ABS like in its strength, with even small details holding up well. I have a 4K printer and the quality is excellent with this resin. The only downside I found was that it did seem to take considerably longer to cure than normal and it was a little harder to clean up excess resin.

bought to use with a Mars 3 4k printer, the resin cures to a nice neutral grey colour and takes paint easily, slightly flexible without being brittle which is good. its not the cheapest resin but since it works I'm not wasting too much time experimenting. using to print gaming models from 6mm scale upwards and to date have not had any issues that I didn't cause myself, on the 6th bottle of it so far

A bit smelly, but works really well (Elegoo MARS 3 pro)...usual precautions required (mask, gloves, goggs, stinky air extraction pump)

I don't know if it's because it's kinda translucent and that the uv light penetrates it better than the other stuff but this stuff sets really well and the quality of the print is excellent. Although the issues of anything flat that you print tends to curl but that happens with every resin I have used just slightly less with this one

very good

Used for prototype work & resin was as described. Little to no shrink & color was great.

ABS-like gray is my go-to for anything that needs to be painted. Red makes amazing prints and behaves with settings the same as gray. BLUE however is very viscous compared to red and I had to double my suppport height to get it to drain and not fuse all of the supports together and ruin the underside of the print. It may have been a bad batch situation, but I went through almost an entire kg bottle of blue before I got it to perform like red. I suspect this is due to blue being more translucent than red and how the color reacts to the UV curing process. I had to shorten my layer time to 2s from 2.5 on the Mars 2 Pro. Support height went from 5mm to 10.

Das Harz lässt sich super drucken. Meine Druckparameter auf dem Elegoo Saturn: - Bottom Layer 15s, 7 Layer (gibt nen Elefantenfuß, bei nem Raft aber nicht schlimm), 0,5s Resting time, 40mm/s bzw. 240mm/min lifting speed, 210-240mm/min retraction speed - Normal layer 2,5s@0,05mm bzw. 3,2s@0,1mm, 0-0,5s Resting time, 180-240mm/min lifting und retraction speed Bin komplett neu im 3D Druck und hab überhaupt keine Erfahrung. Das hier waren meine ersten 4 Drucke, kein Fehldruck dabei. Das Harz sieht schon so aus dem Drucker klasse aus, mit Klarlack lackiert wird daraus aber wirklich eine Augenweide (die Miniaturen sind mit Klarlack überzogen). Zur Einordnung der Druckgrößen: Mini-Figuren max Kantenlänge vom Boxmaß 25mm, das Brandenburger Tor hingegen 170mm auf der langen Seite und nimmt damit fast die gesamte Druckfläche des Saturn ein. Der Geruch ist schon streng (im Vergleich zum Anycubic Plant-based), bleibt aber bei geschlossener Tür im Druckzimmer. Das Harz hat eine gewisse Elastizität, ist also nicht super spröde und verzeiht auch mal nen kleinen Sturz auf den Boden. Es wirkt aber trotzdem stabil. Beispiel: wenn man die Photonsters Validation Matrix druckt, bleibt die Platte schön eben, ist aber biegbar. Mit dem Anycubic plant based resin verzieht sich die gleiche Platte stärker.

Nothing but failed prints that were 100% successful with other resin. Waste of money and time. Wouldn't stay on the build plate, have holes in walls that require no support. Tried several different settings with no luck. New screen and it just keeps failing...

Would have loved to print with it but most of it was in the bag because it wasn't sealed correctly when manufactured. I'm extremely disappointed. On the phone with amazon to see what we can do about it.