RBP-017 Rear Bumper Protector

The RBP-017 offers durable, easy-to-install protection for your vehicle's rear bumper. Its fits my 2020 Chrysler Pacifica perfectly. It provides comprehensive coverage against scratches and dings. The sleek design maintains my bumper's integrity without breaking the bank. Highly recommended for its effective functionality and cost-effectiveness. Much cheaper than the OEM one that was an option at the dealer.Just buy it! Cheaper than repainting your bumper!

Very nice product. Fit well. should last the life of the van. I like it. Easy install.

Install was easy. Seems well made. Does great at protecting the bumper from damage while loading and unloading.

I got this about $5 cheaper getting it from the Amazon warehouse, which can be hit and miss. Beforehand, I fished through the reviews and decided to take a chance on it. The reviews did help for installation as it didn't come with any instructions. Go figure...thanks amazon warehouse. So, as it comes out of the box and you lay it down on the bumper. It looks like it will not fit right as the bumper pad doesn't align correctly. Don't worry, when you decide to do the final install it will curve into place. Here are some helpful points that I learned during the install...1. Use a cleaner, then an alcohol pad or similar to clean the bumper for better adhesion.2. Use painters tape or such to help guide the edges. It will help somewhat.3. Take all the 3m tape off the back so it lays down easier. Taking one side and peeling it off as you lay it down will not help at all.4. Make sure you keep track of the arrow in the middle of the bumper pad as you lay it down. It should be as close as you can get it to the rear trunk door hitch. It will help you keep the bumper pad even on both sides.5. Don't worry about laying the bumper pad down wrong on the one side you start on. Just don't firmly press the pad down on the bumper until you are sure that is where you want to set it. I ended up lifting the bumper pad off the bumper a few times before I felt like it was where I wanted to stay. Once you press it on firmly, it's pretty much on.So, time will tell if this stay on or comes off. But for now, it hides the scratches on the bumper very well and seems to have tight grip on it as well. Don't really know if this is worth $65-$70, but still better then what else is out there. Hope this helps. Good luck.Update: I've had the bumper pad installed for a couple of months now. Still looks great and is still has a good firm grip on my bumper.

A solid 4. A little more flimsy than I expected but seems durable. At $60+ I probably would have waited for more options on the market. We recently purchased a preowned 2017 Pacifica and it’s almost flawless with the exception of the rear bumper which had nicks and chips through the paint that was quite noticeable. So This purchase was for protection and to cover the cosmetic damage. It looks good and It’s got a good fit although I’d like the lip that covers the edge of the bumper to be a tad bit longer. I reinforced the bottom with more 3m automotive sticky tape. Make sure you read the instructions. If you lay it down on the bumper to see how it fits it will seem that it doesn’t. It’s flexible and curves with your bumper for a near perfect fit.. Just line up the arrow with your trunk latch and curve then stick down a side at a time. I also used a heat gun to improve stickiness of 3m tape. I’m sure a blow dryer would suffice if you dont have one.

This was not actually designed for a 2020 Chrysler Pacifica.. its a one size fits all years kind of deal. It is less expensive than having to repaint a bumper cover, ( had my Pacifica one week and already chipped). I found it rather easy to install, but I am not confident that it will stay in place with the Texas heat. This does not go all the way up to the sill of the door, and it does not cover the width of the door frame either. I think that if it remains stuck it was worth the investment even though it is overpriced for what it is. Too bad Chrysler omitted this guard on the Pacifica , they put them on the old Town & Country Van, and on the Dodge Caravan's so why not the Pacifica.... Thanks Chrysler. The 4 stars is because I am concerned that it will eventually come off the vehicle. On 30 Jun 2022, I purchased another bumper guard for my 2022 Pacifica Limited, this time I purchased and installed it before the paint got damaged. Its about the best one even if it is a little expensive. I recommend it. Ok, so today, 19 Dec 2022, I received another Bumper guard for my new 2022 Chrysler Pacifica Touring L . I have confidence after the previous installs that this one will last as well. I still wish Chrysler would install them as it doesn't make sense not to have one. I have bumped it to 5 stars and recommend it to anyone who needs a bumper guard.

Read tips prior to install. Clean the bumper and dry. Easier with 2 people - one to hold/press and another to remove sticker paper. Line up the middle with middle of trunk area without removing the paper on the stickers. Place where will go and see how you will press down and then move outward, leaving a slight over hang per the instructions. Then remove the middle sticker cover first - about 6 inches top and bottom, tearing it off and press just the middle to the bumper for 30 seconds, then remove more sticker paper on one side and push into place to follow the curve of the bumper and press for 30 seconds, then continue with this until you are done on both sides.What we did then was take a hair dryer and turned to high and heated an area in a sweeping motion for about 20 secs and pressed/held in across the whole bumper to help secure a good adhesion - I used a knit hat to help block the heat from my hands while I pressed one area and heated the adjacent area and kept moving every 20 secs or so.Looks and feels good - was easy to install and we were done within minutes after receiving the product.